Honeywell TRADELINE VR8204A Скачать руководство пользователя страница 14

68-0047—2

14

VR8204; VR4204

SERVICE

!

INSTRUCTIONS TO THE HOMEOWNER
FOR YOUR SAFETY, READ BEFORE OPERATING

WARNING

IF YOU DO NOT FOLLOW THE
WARNINGS BELOW AND THE
LIGHTING INSTRUCTIONS EXACTLY,
A FIRE OR EXPLOSION CAN RESULT
WITH PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
1. Before lighting, smell around the appliance

area for gas. If the appliance uses LP (bottled)
gas, be sure to smell next to the floor because
LP gas is heavier than air. If you smell gas,
immediately shut off the manual valve in the
gas piping to the appliance or, on LP, at the
tank
. Do not try to light any appliance. Do not
touch any electrical switch or use the phone.
Leave the building and call your gas supplier.
If your gas supplier cannot be reached, call the
fire department.

2. Do not force the gas control knob on the appli-

ance. Use only your hand to turn the gas con-
trol knob. Never use any tools. If the knob will
not operate by hand, replace the control using a
qualified service technician. Force or attempted
repair can result in fire or explosion.

3. The gas control must be replaced if it has been

flooded with water. Call a qualified service
technician.

4. The gas control is a safety device. It must be

replaced in case of any physical damage such
as bent terminals, missing or broken parts,
stripped threads, or evidence of exposure to
heat.

IMPORTANT: Follow the operating instructions pro-

vided by the manufacturer of your heating appliance.
The information below will be of assistance in a
typical control application, but the specific controls
used and the procedures outlined by the manufac-
turer of your appliance may differ, requiring special
instructions.

TO TURN ON FURNACE
STOP! Read the safety information above.

1. The lighting sequence on this appliance is automatic;

do not attempt to manually light the pilot.

2. If the furnace does not come on when the thermostat

is set several degrees above room temperature, set the
thermostat to the bottom of its range to reset safety control.

3. Remove the burner access panel if provided on your

appliance.

4. Turn the gas control knob (Fig. 5) clockwise

to

OFF.

5. Wait five minutes to allow any gas in the combustion

chamber to vent. If you then smell gas in the appliance area
or near the floor in an LP installation, immediately shut off
the manual valve in the gas piping to the appliance or, on
LP, at the tank
. Do not touch any electrical switch or use the
phone. Do not try to light any appliance. Leave the building
and call your gas supplier. If your gas supplier cannot be
reached, call the fire department. Failure to do so may result
in fire or explosion.

6. If you don’t smell gas, turn knob on gas control

counterclockwise

to ON.

7. Replace burner access panel.
8. Reset thermostat to desired temperature.
9. If appliance will not operate, turn the gas control

knob to OFF and contact a qualified service technician for
assistance.

TO TURN OFF APPLIANCE
VACATION SHUTDOWN: Set the thermostat to the de-

sired room temperature while you are away.

COMPLETE SHUTDOWN: Push in the gas control knob

slightly and turn clockwise

to OFF. Do not

force. Appliance will completely shut off. Follow the
Instructions to the Homeowner above to resume nor-
mal operation.

Содержание TRADELINE VR8204A

















Отзывы: