Honeywell Titan SCBA Скачать руководство пользователя страница 9

3

Honeywell Titan SCBA, 2013

2

WARNING—CONTINUED

• ONLY grasp the cylinder valve handwheel 

to open or close the valve. DO NOT pick up 

or carry a cylinder by the handwheel, drop 

a  cylinder  on  the  handwheel,  or  bump  the 

handwheel, as this may cause the cylinder 

valve to inadvertently open, which may lead 

to the cylinder becoming airborne under the 

thrust of air released from the open valve, 

causing  injury  or  death.  ALWAYS  pick  up 

and  carry  an  air  cylinder  by  the  cylinder 

body.

•  Do  not  over-torque  air  cylinder  valves. 

ALWAYS  verify  that  the  hydrostatic  test 

facility  performing  your  cylinder  testing 

DOES NOT over-torque the cylinder valves 

when they reinstall them.

•  Some  CBRN  agents  may  not  present 

immediate  effects  from  exposure,  but  can 

result  in  delayed  impairment,  illness,  or 

death.

• Direct contact with CBRN agents requires 

proper handling of the SCBA after each use 

and  between  multiple  entries  during  the 

same use. 

• Decontamination and disposal procedures 

must  be  followed.  If  contaminated  with 

liquid  chemical  warfare  agents,  dispose  of 

the SCBA after decontamination.

•  The  respirator  should  not  be  used 

beyond  six  (6)  hours  after  initial  exposure 

to  chemical  warfare  agents  to  avoid  the 

possibility of agent permeation.

•  Prior  to  using  the  Titan  SCBA  for  the 

fi rst  time,  you  must  perform  fi t  testing  as 

described  in  section  VI.  Do  not  wear  this 

respirator if a satisfactory fi t, as determined 

by  the  fi t  testing  described  in  section  VI, 

cannot be obtained.

• You must read, understand, and follow all 

warnings,  instructions,  labels,  and  Safety 

Data  Sheets  (SDS),  etc.,  for  the  materials 

you  are  using  (e.g.,  paints, hardeners, 

insecticides, varnishes, etc.).

• You must also read, understand, and follow 

all warnings, instructions, etc., listed in the 

SDS  for  any  contaminants  that  may  be  or 

are present in the work area.

•  FAILURE  TO  COMPLY  WITH  THESE 

WARNINGS  MAY  RESULT  IN  PERSONAL 

INJURY, ILLNESS, OR DEATH.

WARNING

Detectable  amounts  of  chemicals  known 

to the State of California to cause cancer, 

birth  defects,  or  reproductive  harm  may 

be  found  in  this  product.  (This  warning 

required  by  California  Health  and  Safety 

Code Section 25249.6)

Part No.

Description

fACEPIECES

282053

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, SMALL BLACK NOSE CUP, SILICONE 

HEADSTRAP

282012

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, MEDIUM BLACK NOSE CUP, SILICONE 

HEADSTRAP

282013

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, LARGE BLACK NOSE CUP, SILICONE 

HEADSTRAP

282041

FACEPIECE—TWENTY/20+, CBRN, MEDIUM, 

BLACK, SMALL BLACK NOSE CUP, SILICONE 

HEADSTRAP

282022

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, MEDIUM BLACK NOSE CUP, SILICONE 

HEADSTRAP

282023

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, LARGE BLACK NOSE CUP, SILICONE 

HEADSTRAP

282043

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, SMALL BLACK NOSE CUP, SILICONE 

HEADSTRAP

282032

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, MEDIUM BLACK NOSE CUP, SILICONE 

HEADSTRAP

282033

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, LARGE BLACK NOSE CUP, SILICONE 

HEADSTRAP

282048

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, SMALL BLACK NOSE CUP, HEADNET

282016

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, MEDIUM BLACK NOSE CUP, HEADNET

282017

FACEPIECE—TWENTY/20+, CBRN, SMALL, 

BLACK, LARGE BLACK NOSE CUP, HEADNET

282050

FACEPIECE—TWENTY/20+, CBRN, MEDIUM, 

BLACK, SMALL BLACK NOSE CUP, HEADNET

282026

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, MEDIUM BLACK NOSE CUP, HEADNET

282027

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, LARGE BLACK NOSE CUP, HEADNET

282052

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, SMALL BLACK NOSE CUP, HEADNET

282036

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, MEDIUM BLACK NOSE CUP, HEADNET

282037

FACEPIECE—TWENTY/20+, CBRN, LARGE, 

BLACK, LARGE BLACK NOSE CUP, HEADNET

282053T

FACEPIECE—TWENTY/20+, CBRN, SMALL,  

BLACK, SMALL BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

282012T

FACEPIECE—TWENTY/20+, CBRN, SMALL,  

BLACK, MEDIUM BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

282013T

FACEPIECE—TWENTY/20+, CBRN, SMALL,  

BLACK, LRG BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

III. PARTS LIST

282041T

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, SMALL BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

282022T

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, MEDIUM BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

282023T

FACEPIECE—TWENTY/20+, CBRN, MEDIUM,  

BLACK, LARGE BLACK NOSE CUP, W/TEMPLE 

INSERTS, SILICONE HEADSTRAP

Содержание Titan SCBA









































Отзывы: