Honeywell Smoke Alarm Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 15

background image

5/19/2008

15 of 15

Option “

g) IP Connectivity

” displays the IP settings that are running in the

device.

•

If the IP Settings were not obtained through DHCP, the fixed ones entered

in “

c) Quick Install

” are displayed, and actually used.

If on the other hand, the IP Settings were dynamically obtained from a DHCP
server, these parameters will be displayed together with other DHCP parameters:
remaining lease time, remaining time until the next DHCP request is sent and the
DHCP server IP address.

«
...
13
14
15

Содержание Smoke Alarm
















Отзывы:

Нет отзывов

Похожие инструкции для Smoke Alarm

Бренд: Hama Страницы: 2

Бренд: Ultra Start Страницы: 16

Бренд: Unitech Страницы: 21

Бренд: La Crosse Technology Страницы: 10

Бренд: HANNspree Страницы: 38

Бренд: Jenile Страницы: 14

Samurai CS-8801SE

Бренд: CrimeStopper Страницы: 11

Бренд: Sidewinder Страницы: 52

Бренд: La Crosse Technology Страницы: 14

Бренд: Audiovox Страницы: 8

Бренд: Audiovox Страницы: 38

Бренд: Trevi Страницы: 8

Бренд: Autostart Страницы: 13

Бренд: Soundcore Страницы: 117

Бренд: IKEA Страницы: 8

Бренд: Black Widow Страницы: 4

Бренд: Black Widow Security Страницы: 4

Бренд: RadioLink Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды