Honeywell PW7K1R1E Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 28

Honeywell PW7K1R1E Скачать руководство пользователя страница 14

14

www.honeywell.com

PW7K1R1E Wiring and Setup

Factory Default Communication Parameters

2.5 Factory Default Communication Parameters

2.6 Bulk Erase

The bulk erase function can be used for the following purposes:

•

Erase all configuration, sets MR62e to OEM setting (sanitize board).

•

Restore to OEM default parameters.

2.7

Bulk Erase Steps

Do not remove power during steps 4-6.

1. Set S1 DIP switches to: 1 & 2 “ON”, 3 & 4 “OFF”.

2. Apply power to the MR62e.

3. Watch for LEDs 1 & 2 and 3 & 4 to alternately flash at a 0.5 second rate.

4. Within 10 seconds from applying power, change switches 1 or 2 to “OFF”. If

these switches are not changed, the MR62e will power up using the OEM
default communication parameters.

5. LEDs 1 and 2 alternately flash at a 0.5 second rate while the memory is being

erased.

6. Once the memory is eased, LED 1 will be on for about 3 seconds, then the

MR62e will reboot.

Table 3: Factory Default Communication Parameters

Network

: static IP address: 192.168.0.251

Subnet Mask

: 255.255.0.0

Default Gateway :192.168.0.1

«
...
12
13
14
15
16
...
»

Содержание PW7K1R1E





























Отзывы:

Нет отзывов