background image

69-0153—3

2

TS86A POWERPILE

®

 THERMOSTAT

Mounting Wallplate on Outlet Box

Use cover ring, TS86A Wallplate Assembly and screws as
shown in Fig. 3.

1. Place the cover ring on the outlet box with the cable

entrance holes toward the bottom.

2. Pull the thermostat cable through the bottom hole.
3. Align the diamonds vertically on the cover ring and

secure with the screws provided.

NOTE:

The side reading Made in U.S.A. must be
against the wall.

4. Position the wallplate assembly and pull the

thermostat cable through the cable entrance hole.

5. Mount wallplate with the screws provided. Tighten

screws after the wallplate is leveled. See Fig. 1 for
leveling instructions.

SPIRIT
LEVEL

DIAMOND
GUIDES (2)

LEVELING
POSTS (2)

MOUNTING
SLOTS

M3831

VERTICAL
PLUMB LINE

OPENING FOR
THERMOSTAT
WIRING

R

W

Y

1

CONNECT WIRING TO R AND W TERMINALS FOR 
750 mV SYSTEMS.  CONNECT TO R AND Y FOR 
250 OR 500 mV SYSTEMS.

1

WALL

1

USE WALLPLATE FOR HEAT APPLICATIONS.

127293 COVER
RING (OPTIONAL)

THERMOSTAT CABLE
ENTRANCE HOLE

NO. 4 X 1 INCH SHEET 
METAL SCREWS (2)

WALLPLATE

M3829A

MOLDED
LEVELING
POST

Fig. 2. Mounting wallplate to wall.

Fig. 3. Mounting wallplate to outlet box.

OUTLET BOX

127293
COVER RING

1

CAPTIVE
SCREWS (3)

THERMOSTAT CABLE
ENTRANCE HOLE

TS86A 
(COVER RING 
REMOVED)

IF OUTLET BOX IS HORIZONTAL, MOUNT COVER RING IN POSITION 
SHOWN, BUT FASTEN WITH SCREWS THROUGH "A".

M3826

Wiring

IMPORTANT

1. Never use any source of power other than a self-

powered millivoltage pilot generator system.
Refer to Fig. 4. Connect a 750 millivolt system to
R and W terminals at wallplate. Connect a 250
or 500 millivolt system to R and Y terminals
at wallplate.

2. This thermostat has a fixed anticipation heater

properly sized for use with self-generating
Powerpile systems. It should not be changed.

3. Use the T87, not the TS86, in systems where the

millivoltage gas valve is controlled through a
switching relay.

All wiring must comply with local codes and ordinances for
wire size and voltage. See Fig. 4 for typical millivolt
hookup.

Fig. 1. Leveling wallplate with spirit level or plumb line.

Содержание Powerpile TS86A

Страница 1: ...ter the wallplate is leveled See Fig 1 for leveling instructions TS86A Powerpile Thermostat APPLICATION The TS86A is a mercury switch thermostat that controls Powerpile millivolt gas systems The millivolt system operates independently of the electrical line service of the home Do not attach this thermostat to any source of power other than a millivolt pilot generator The wallplate adapts the TS86A...

Страница 2: ...LICATIONS 127293 COVER RING OPTIONAL THERMOSTAT CABLE ENTRANCE HOLE NO 4 X 1 INCH SHEET METAL SCREWS 2 WALLPLATE M3829A MOLDED LEVELING POST Fig 2 Mounting wallplate to wall Fig 3 Mounting wallplate to outlet box OUTLET BOX 127293 COVER RING 1 CAPTIVE SCREWS 3 THERMOSTAT CABLE ENTRANCE HOLE TS86A COVER RING REMOVED IF OUTLET BOX IS HORIZONTAL MOUNT COVER RING IN POSITION SHOWN BUT FASTEN WITH SCRE...

Страница 3: ... breaks contact M3834 6 0 9 0 80 70 60 9 0 15 1 2 2 6 8 1 0 5 4 3 CALIBRATION NUT Fig 5 Recalibration procedure TS86A POWERPILE THERMOSTAT HIGH LIMIT CONTROL CIRCLED WIRING MUST BE APPROVED SAFETY CIRCUIT WIRING USE R AND W TERMINALS FOR A 750 mV SYSTEM USE R AND Y TERMINALS FOR A 250 OR 500 mV SYSTEM 2 W R Y TH M3832 1 1 TH PP PP POWERPILE PILOT GENERATOR POWERPILE GAS VALVE 2 Fig 4 Typical Power...

Страница 4: ...Wait at least five minutes 4 Slowly turn the dial until the pointers read the same 5 Firmly hold the dial from turning and carefully turn the hex nut counterclockwise until the mercury just slips to the heating contact end of tube but no farther 6 Recheck calibration select the desired temperature and replace the cover After the installation is complete the homeowner can paint the TS86 cover to ma...

Отзывы: