manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 54 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 54

54

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Configuration

Programming and Testing the Smoke Control Station 

This completes the SCS-8L⁄SCE-8L installation. After programming the fire alarm control panel to accept the SCS-8L⁄SCE-8L, fully test the 
system to ensure that each switch performs its intended function, each LED lights as required, and that the SCS-8L⁄SCE-8L can perform the 
functions outlined in Section 3.8.1 “Firefighter's Smoke Control Station (FSCS) Mode” (if operating in FSCS Mode) or Section 3.8.2 “Heat-
ing, Ventilating & Air Conditioning (HVAC) Mode” (if operating in HVAC Mode).

3.8  Configuration

3.8.1  Firefighter's Smoke Control Station (FSCS) Mode

The Firefighter's Smoke Control Station (FSCS) Mode is enabled when dipswitch six on the SCS is in the ON position (see Table 3.4). In this 
mode, the SCS⁄SCE becomes the FSCS and is intended to have the highest priority over associated fan and damper functions. For a fan or 
damper to be used in a smoke control system, the system must not only be able to control the device, but it must be able to verify what state 
it is in (ON/OFF or OPEN/CLOSED). Correct installation of the control and monitor modules associated with the SCS⁄SCE is vital to ensure 
proper operation. Each toggle switch group is assigned a switch group type number (see Table 3.3) which is referenced in the text, tables, and 
appendices identifying the configuration, connection, and operation of associated equipment.

Operating in FSCS mode, the SCS⁄SCE is capable of Dedicated and Non-dedicated System operation. When dipswitch 7 is in the ON posi-
tion, the SCS⁄SCE operates as a Dedicated System; in the OFF position the SCS⁄SCE operates as a Non-dedicated System (see Dedicated 
System Operation and Non-dedicated System Operation headings later in this section).

SCS Dipswitch Settings for FSCS Mode

Table 3.5 describes the dipswitch settings necessary to configure the SCS⁄SCE for many variations of controlling smoke. Although the con-
figurations are shown with an SCE, the configuration for the SCS is the same as it is shown in the table if an SCE is not used. Each descrip-
tion of a dipswitch setting follows the format shown below: 

NOTE:

Refer to the “Restrictions” section of this manual for information on compatible software part numbers.

NOTE:

ONYX Series FACPs and associated network annunciators are only compatible with SCS software #SCS2.84 or higher. They are 

not compatible with any 73XXX series software versions.
To use the SCS V4.0, NFS2-3030, and/or NCA-2 must be running software V21 or higher. 

19 

When used with an SCE, eight switch groups are 
available for group type 8 operation and eight are 
available for group type 1 operation in the format 
shown to the left. Type 8 switch groups require two 
control modules and one monitor module. Type 8 
switch groups are usually only used for fans. One 
control module is used for the ON control of the fan, 
the other control module is used for the OFF control. 
The monitor module is used for the ON verification of 
the fan. Type 1 switch groups require one control 
module and one monitor module. Type 1 switch 
groups can be used for fans or dampers. The control 
module is used for OFF control of a fan and the 
monitor module is used for the OFF verification of the 
fan.

8

8

8

8

1

1

1

1

1

1

1

1

8

8

8

8

SCS-8

SCE-8

OFF

ON

Switches 1-5 select 
the SCS⁄SCE for a 
particular configuration 
of switch group types

Switch 6, when in the 
ON position, selects 
FSCS Mode.

See Table 3.4 for settings of 
switches 7 and 8.

Reference 

Number

This diagram depicts the layout of the switch 
groups and the group type associated with 
each switch group for the particular 
dipswitch setting on the right.

This text describes the functions, 
capabilities, and limitations of the 
SCS⁄SCE for the particular dipswitch 
setting.

This diagram depicts the dipswitch 
setting necessary to configure the 
SCS⁄SCE for the capabilities 
mentioned to the left.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов