manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 38 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 38

38

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Preliminary SCS-8⁄SCE-8 Design Considerations

Usually a fan does not need the capability of separate verification of its on/off state (requiring two monitor modules). One monitor module is 
capable of determining when the fan is on and when it is off.

3.4.5  Switch Group Type

Each controlled/monitored fan or damper has one associated switch group on the SCS⁄SCE. Each switch group has four EIA-485 protocol 
points used to control and monitor a fan or damper. There are four stand-alone capabilities available for controlling and monitoring fans and 
dampers for smoke control:

•

The capability to turn a fan on (open a damper), regardless of its current state

•

The capability to turn a fan off (close a damper), regardless of its current state

•

Monitor and verify when the fan is on (or when damper is open)

•

Monitor and verify when the fan is off (or when damper is closed)

If a fan or damper requires all four of these capabilities, then two control modules and two monitor modules must be connected to the device 
and one protocol point would be responsible for each of the four capabilities. A control module is assigned either an ON⁄OPEN or an 
OFF⁄CLOSED capability to control a fan or damper.

ON⁄OPEN Control (CON

ON⁄OP

)

 - turn a fan on (or open a damper)

OFF⁄CLOSED Control (CON

OFF⁄CL

) 

- turn a fan off (or close a damper)

A monitor module is assigned an ON⁄OPEN or an OFF⁄CLOSED capability for verification of the state of a fan or damper.

ON⁄OPEN Verification (VER

ON⁄OP

)

 - verify when a fan is on (or verify when a damper is open)

OFF⁄CLOSED Verification (VER

OFF⁄CL

) 

- verify when a fan is off (or verify when a damper is closed)

These four capabilities, now referred to as 

CON

ON⁄OP

, 

CON

OFF⁄CL

, 

VER

ON⁄OP

 and 

VER

OFF⁄CL

, can be applied to the nine scenarios as 

shown in Table 3.3. These nine combinations represent all the capabilities a fan or damper can have for smoke control. The capabilities of 
each fan or damper must match one of these nine scenarios. Each scenario is referred to as a switch group type.

Example:

 If a fan must have the capability of on and off control, as well as verification of when the fan is on, you would 

need switch group type 8.

3.4.6  Switch Group Type Configuration

Once the switch group types have been selected, they must be configured for the SCS⁄SCE. The configuration of switch group types will 
determine the number of SCS⁄SCE modules required for the system. The configuration layouts must be selected from pre-chosen formats 
shown in the tables in Section 3.8 “Configuration”. Although the configurations in these tables are shown with an SCE, the configuration is 
the same for the SCS if an SCE is not used. 

Table 3.3  FSCS Mode Switch Group Types

1

CON

OFF⁄CL

 and 

VER

OFF⁄CL

Turn a fan off (close a damper) and verify when the fan is off (damper closed)

2

CON

OFF⁄CL

 and 

VER

ON⁄OP

 

Turn a fan off (close a damper) and verify when the fan is on (damper open)

3

CON

OFF⁄CL

, 

VER

ON⁄OP

 and 

VER

OFF⁄CL

Turn a fan off (close a damper) and verify when the fan is on and off (damper open and closed)

4

CON

ON⁄OP

 and 

VER

OFF⁄CL

 

Turn a fan on (open a damper) and verify when the fan is off (damper closed)

5

CON

ON⁄OP

 and 

VER

ON⁄OP

 

Turn a fan on (open a damper) and verify when the fan is on (damper open)

6

CON

ON⁄OP

, 

VER

ON⁄OP

 and 

VER

OFF⁄CL

 

Turn a fan on (open a damper) and verify when the fan is on and off (damper open and closed)

7

CON

ON⁄OP

, 

CON

OFF⁄CL

 and 

VER

OFF⁄CL

Turn a fan on and off (open and close a damper) and verify when the fan is off (damper closed)

8

CON

ON⁄OP

, 

CON

OFF⁄CL 

and 

VER

ON⁄OP

Turn a fan on and off (open and close a damper) and verify when the fan is on (damper open)

9

CON

ON⁄OP

, 

CON

OFF⁄CL, 

VER

ON⁄OP

 and 

VER

OFF⁄CL

Turn a fan on and off (open and close a damper) and verify when the fan is on and off (damper open and closed)

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов