manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 47 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 47

SCS Series Manual —

 P/N 15712:L  7/18/16

47

SCS-8L⁄SCE-8L Installation

The SCS⁄SCE

Programming and Testing the Smoke Control Station 

This completes the SCS-8⁄SCE-8 installation. After programming the fire alarm control panel to accept the SCS-8⁄SCE-8, fully test the sys-
tem to ensure that each switch performs its intended function, each LED lights as required, and that the SCS-8⁄SCE-8 can perform the func-
tions outlined in Section 3.8.1 “Firefighter's Smoke Control Station (FSCS) Mode” (if operating in FSCS Mode) or Section 3.8.2 “Heating, 
Ventilating & Air Conditioning (HVAC) Mode” (if operating in HVAC Mode).

3.7  SCS-8L⁄SCE-8L Installation

Custom Graphic Annunciators

If a designer is using SCS-8L⁄SCE-8L modules for the system design, the modules must be mounted in a graphic annunciator backbox and 
interfaced with switches and lamps on the faceplate. Ensure that selected backboxes are UL-listed for the combination according to the UL 
category code UUKL. See Appendix C, “Special Applications”, on page 202 for a sample application. 

CHS-4L Installation

The SCS-8L⁄SCE-8L modules mount on four standoffs inside of a custom graphic annunciator cabinet. Alternately, the modules can be 
installed in a standard CHS-4L low-profile chassis for mouning in a cabinet.

Slip the bottom edge of the SCS-8L into the first slot on the chassis, swing the module towrard the standoffs and secure it to the chassis with 
the screws provided, as shown in Figure 3.18. If an SCE-8L is required, plug one end of the annunciator expander ribbon cable into connec-
tor J1 on the SCS-8L. Connect the other end of the annunciator expander ribbon cable to connector J1 on the SCE-8L. Slip the bottom edge 
of the SCE-8L into the second slot on the chassis and swing the module toward the standoffs and secure it to the chassis with the screws pro-
vided. Repeat this procedure for the second set of SCS-8L⁄SCE-8L modules to be installed in positions 3 and 4 on the chassis. Connect the 
wiring as shown in Figure 3.19, Figure 3.20, Figure 3.21, and Figure 3.22.

Regulated power-limiting 

power supply listed for fire 

protective signaling.

(+) 24 VDC 

Power

(–) 24 VDC 

Common

(+) 24 VDC Power 

to SCS-8 TB1-3

(–) Common

to SCS-8 TB1-5

Figure 3.17  Power Supply Connections

NOTE:

Refer to the “Restrictions” section of this manual for information on compatible software part numbers.

NOTE:

The SCS-8L⁄SCE-8L can only be mounted in the CHS-4L chassis for the HVAC mode. If using the FSCS mode the SCS-8L⁄SCE-

8L must be installed in a custom graphic annunciator backbox.

c

Figure 3.18  Installing SCS-8L⁄SCE-8L Modules

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов