manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 206 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 206

206

SCS Series Manual —

 P/N 15712:L  7/18/16

Special Applications

Pairing

– FSCS mode: DEDICATED, NON-DEDICATED. 

– HVAC mode: ENABLE, DISABLE. 

•

Dipswitch setting.

 Displays options configured as in Table 3.3. 

Binary value

 sequence: switch 7 to switch 1. 

Hexadecimal value

 after 

slash. 

•

Trouble reporting delay.

 Displays the number of seconds programmed for the panel’s adjustable trouble delay timer. 

C.4.1  History/Printer

Figure C.6 shows a sample LCD display for a trouble event:

Figure C.6  Event History Example: Trouble Condition

•

Event type. 

This example shows the options for a trouble event.

•

Annunciator label (partial). 

First 16 characters of the SCS-8’s user-programmed text label.

•

Switch-group number.

 Switch-group number is displayed for external troubles.

•

Trouble type. 

ANNUN xx TROUBLE; ANNUN xx NO ANSWER.

•

Enhanced trouble type.

 These provide more detail on the trouble (DIP SW DEFAULT; MODE CONFIG; EXPANDER CONFIG) or 

external trouble (SGxx DEVICE MISMATCH; SGxx DEVICE TROUBLE; SGxx DIP SW MISMATCH; SGxx TIME OUT).

C.5  Pairing

Definition

Pairing (SCS Mode A) allows SCS modules to be “grouped” so that more than one FSCS module will act as a single FSCS module. All 
paired FSCS modules will enter manual mode when any toggle switch is used to enter manual mode. (See NFS2-3030/NCA-2 documenta-
tion.) 

Programming

Programming Requirements:

•

The NFS2-3030/NCA-2 must be programmed for SCS Mode A.

•

Paired module addresses must be configured in the NFS2-3030/NCA-2. 

•

Paired modules must be configured for FSCS mode. 

•

For CBE lockout, program points 65-96 on the first FSCS module only. 

•

Software versions must match those described above.

C.6  Custom Graphic Annunciator with White Light Indication

In applications where the local AHJ requires a white light, logic equation operators (NORM, AUTO) can be used with SCS-8L and LDM-
32(s) to produce the required state.

See NFS2-3030/NCA-2 documentation for logic equation programming.

Examples

1.

SCS shall indicate NORMAL when all SCS switch groups are in the AUTO position:

                            Z L = O R ( A U T O ( A 2 5 ) )

2.

SCS shall provide a NORMAL indication for an individual switch group:

                            Z L = O R ( A U T O ( A 2 5 G 1 ) )

3.

SCS NORMAL state indication includes AC monitoring for control point:

                            Z L = A N D ( N 3 L 1 M 1 , N O R M ( A 2 5 G 1 ) )

(where N3L1M1 represents a monitor module used to monitor the equipment control power).

Trouble Type

Event Type

TROUBLE                                  ANNUN 25 TROUBLE                       

ACS BOARD LABEL  SG01 TIME OUT           09:04:09A WED NOV 13, 2013 N001       

Switch-group Number

Annunciator Label 
(partial)

Enhanced Trouble Type

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов