The Kit PSU7A Assembly (PN: 020-579) is simple to fit to an ID2000/3000 Series Extended Deep Back Box or in a Remote
Battery/PSU Enclosure, providing the instructions described below are followed. The PSU must be fitted BEFORE
installing the main chassis in the Back Box. The PSU Assembly is secured to the Back Box or Remote Battery/PSU
Enclosure using
four M4 x 16 SEM
screws and nylon spacers. A DTP/Booster module MUST be fitted to the ID3000
chassis when using a PSU7A.
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
ATTENTION
ATTENTION
A Cautionary Note....
A Cautionary Note....
Check Your Equipment....
Check Your Equipment....
Taking suitable precautions, before proceeding with the installation, remove all
packaging and inspect contents for any damage that may have occurred during
transit. If no damage is evident, proceed using the instructions below. In the
unlikely event that damage has occurred, or any items are missing, DO NOT
PROCEED, contact your supplier and refer to the panel Installation &
Commissioning Manual.
Observing all necessary precautions, proceed with the installation of the PSU
Assembly to the Back Box.
During this procedure, various wiring connections are to be made and it is
important that the manufacturer’s recommendations are followed to avoid the
possibility of damage occurring to wiring when fitting the PSU Assembly.
Procedure for Fitting the Kit PSU7A
Assembly into a Deep Back Box
It is recommended that the PSU end of all wiring connections
(see overleaf) is made BEFORE the PSU assembly is fitted into
the Back Box.
To fit the PSU assembly (A) into the Back Box, proceed as
follows:
1
Place one of the nylon spacers (B) supplied in the kit over
each of the four larger stand-offs (C) on the rear wall of the
Back Box, then screw one of the M4 x 16 SEM screws (D)
approximately 2 or 3 rotations into each stand-off - DO NOT
FULLY TIGHTEN.
2
Hang the PSU assembly (A) over the screws - orientate it so
that the
mains socket (E) is to the right - then fully tighten the
screws.
3
Refer to PSU wiring instructions overleaf.
Your Kit PSU7A, PN: 020-579, should contain:
PSU Assembly
PN: 010-114
M4 x 16 SEM screws (4 off)
PN: 776-043
Nylon spacers (4 off)
PN: 423-309
Battery interlink cable
PN: 082-218
Orange wire (1 off)
PN: 982-198
Green wire (1 off)
PN: 982-201
Ribbon cable assembly with ferrite
PN: 082-171-003
Thermistor assembly
PN: 082-223
Battery lead, 50/0.25, Red (1 off)
PN: 082-214-005
Battery lead, 50/0.25, Black (1 off)
PN: 082-214-006
Red wire (1 off)
PN: 914-161
Black wire (1 off)
PN: 914-162
Ferrite (1 off)
PN: 670-068
IEC Cable assembly
PN: 082-254
Cable clips (4 off)
PN: 233-229
Cable tie
PN: 233-144
Fuse T 10A H
PN: 570-153
2-way link connector (2 off)
PN: 542-074
Ratings Label
PN: 345-405
Anti-Static Warning instructions
PN: 997-180
Your Kit PSU7A, PN: 020-579, should contain:
PSU Assembly
PN: 010-114
M4 x 16 SEM screws (4 off)
PN: 776-043
Nylon spacers (4 off)
PN: 423-309
Battery interlink cable
PN: 082-218
Orange wire (1 off)
PN: 982-198
Green wire (1 off)
PN: 982-201
Ribbon cable assembly with ferrite
PN: 082-171-003
Thermistor assembly
PN: 082-223
Battery lead, 50/0.25, Red (1 off)
PN: 082-214-005
Battery lead, 50/0.25, Black (1 off)
PN: 082-214-006
Red wire (1 off)
PN: 914-161
Black wire (1 off)
PN: 914-162
Ferrite (1 off)
PN: 670-068
IEC Cable assembly
PN: 082-254
Cable clips (4 off)
PN: 233-229
Cable tie
PN: 233-144
Fuse T 10A H
PN: 570-153
2-way link connector (2 off)
PN: 542-074
Ratings Label
PN: 345-405
Anti-Static Warning instructions
PN: 997-180
The Kit PSU7A Assembly (PN: 020-579) is simple to fit to an ID2000/3000 Series Extended Deep Back Box or in a Remote
Battery/PSU Enclosure, providing the instructions described below are followed. The PSU must be fitted BEFORE
installing the main chassis in the Back Box. The PSU Assembly is secured to the Back Box or Remote Battery/PSU
Enclosure using
four M4 x 16 SEM
screws and nylon spacers. A DTP/Booster module MUST be fitted to the ID3000
chassis when using a PSU7A.
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
ATTENTION
ATTENTION
A Cautionary Note....
A Cautionary Note....
Check Your Equipment....
Check Your Equipment....
Taking suitable precautions, before proceeding with the installation, remove all
packaging and inspect contents for any damage that may have occurred during
transit. If no damage is evident, proceed using the instructions below. In the
unlikely event that damage has occurred, or any items are missing, DO NOT
PROCEED, contact your supplier and refer to the panel Installation &
Commissioning Manual.
Observing all necessary precautions, proceed with the installation of the PSU
Assembly to the Back Box.
During this procedure, various wiring connections are to be made and it is
important that the manufacturer’s recommendations are followed to avoid the
possibility of damage occurring to wiring when fitting the PSU Assembly.
Procedure for Fitting the Kit PSU7A
Assembly into a Deep Back Box
It is recommended that the PSU end of all wiring connections
(see overleaf) is made BEFORE the PSU assembly is fitted into
the Back Box.
To fit the PSU assembly (A) into the Back Box, proceed as
follows:
1
Place one of the nylon spacers (B) supplied in the kit over
each of the four larger stand-offs (C) on the rear wall of the
Back Box, then screw one of the M4 x 16 SEM screws (D)
approximately 2 or 3 rotations into each stand-off - DO NOT
FULLY TIGHTEN.
2
Hang the PSU assembly (A) over the screws - orientate it so
that the
mains socket (E) is to the right - then fully tighten the
screws.
3
Refer to PSU wiring instructions overleaf.
Your Kit PSU7A, PN: 020-579, should contain:
PSU Assembly
PN: 010-114
M4 x 16 SEM screws (4 off)
PN: 776-043
Nylon spacers (4 off)
PN: 423-309
Battery interlink cable
PN: 082-218
Orange wire (1 off)
PN: 982-198
Green wire (1 off)
PN: 982-201
Ribbon cable assembly with ferrite
PN: 082-171-003
Thermistor assembly
PN: 082-223
Battery lead, 50/0.25, Red (1 off)
PN: 082-214-005
Battery lead, 50/0.25, Black (1 off)
PN: 082-214-006
Red wire (1 off)
PN: 914-161
Black wire (1 off)
PN: 914-162
Ferrite (1 off)
PN: 670-068
IEC Cable assembly
PN: 082-254
Cable clips (4 off)
PN: 233-229
Cable tie
PN: 233-144
Fuse T 10A H
PN: 570-153
2-way link connector (2 off)
PN: 542-074
Ratings Label
PN: 345-405
Anti-Static Warning instructions
PN: 997-180
Your Kit PSU7A, PN: 020-579, should contain:
PSU Assembly
PN: 010-114
M4 x 16 SEM screws (4 off)
PN: 776-043
Nylon spacers (4 off)
PN: 423-309
Battery interlink cable
PN: 082-218
Orange wire (1 off)
PN: 982-198
Green wire (1 off)
PN: 982-201
Ribbon cable assembly with ferrite
PN: 082-171-003
Thermistor assembly
PN: 082-223
Battery lead, 50/0.25, Red (1 off)
PN: 082-214-005
Battery lead, 50/0.25, Black (1 off)
PN: 082-214-006
Red wire (1 off)
PN: 914-161
Black wire (1 off)
PN: 914-162
Ferrite (1 off)
PN: 670-068
IEC Cable assembly
PN: 082-254
Cable clips (4 off)
PN: 233-229
Cable tie
PN: 233-144
Fuse T 10A H
PN: 570-153
2-way link connector (2 off)
PN: 542-074
Ratings Label
PN: 345-405
Anti-Static Warning instructions
PN: 997-180
Access to components inside the safety cover of the PSU7A is
not required for installation and commissioning purposes.
There is no need to remove the safety cover to replace any
fuses, as with earlier versions of the PSU7A, as these are
located on the PCB outside the cover.
B (x4)
D (x4)
C (x4)
A
E
Installing the Kit PSU7A Assembly
VIEW
A
'A'
CAUTION SURFACE
MAY BE HOT
NOTE:
1
by Honeywell
997-277-000-9, Issue 9 February 2010
