Honeywell Modutrol IV M945F Скачать руководство пользователя

Страница: 6 / 12

SERIES 90 MODUTROL IV™ MOTORS

63-2631

Fig. 3. Mounting the motor with an adapter bracket.

Damper Linkages

The motor does not include a crank arm. Order the crank arm,

included in the Q605 Linkage, separately (see Accessories in

the Specifications section). For detailed instructions on the

assembly of specific linkages, refer to the instruction sheet

packed with the linkage.

CAUTION

Equipment Damage Hazard.

Stalling a motor can damage the drive shaft.

Ensure installation of motors and linkages allows the

motor to drive through full stroke without obstruction.

Valve Linkages

The Q100 Linkage requires the 220738A Adapter Bracket for all

valve applications. Applications with the Q5001 Valve Linkage

do not require the 220738A Adapter Bracket (see Fig. 4).

Junction Box

When used with liquid-tight conduit connectors, the junction

box provides NEMA 3 weather protection for the motor. The

junction box, standard with replacement motors, encloses the

terminals and provides knockouts for wiring conduits. Housing

an internal transformer or internal auxiliary switches requires

use of the junction box.

Fig. 4. Mounting the motor on a Q5001 Valve Linkage.

M18999

EQUIPMENT

BASE

ADAPTER

BRACKET

STANDARD

BOLTS (4)

MOTOR

BOLTS

PROVIDED (4)

WIRING

BOX

NON-SPRING RETURN

SPRING RETURN

1 #12 OR 1/4" ZINC PLATED

MACHINE SCREWS OR BOLTS

POWER

END

POWER END

1/4-20 UNC

1 in. LONG

MOUNTING

BOLTS

Q5001

VALVE

LINKAGE

M18994

MOTOR

JUNCTION

BOX

POWER

END OF

MOTOR

VALVE

Содержание Modutrol IV M945F













Результаты поиска

Содержание Modutrol IV M945F

Отзывы:

Похожие инструкции для Modutrol IV M945F

Бренды по названию

Популярные бренды

Honeywell Modutrol IV M945F, Данные о продукции

Результаты поиска

Содержание Modutrol IV M945F

Отзывы:

Похожие инструкции для Modutrol IV M945F

Бренды по названию

Популярные бренды