Honeywell LYNXDM-GSM, Инструкция по установке и настройке, Страница: 3 / 16

- 3 -
2. Route the incoming power, telephone and/or internet wiring through the appropriate openings in the
mount’s rear case.
3. Mount the rear case to a sturdy wall using the four screws (supplied).
4. Route incoming power, telephone and communications, etc. wiring through the mount’s front case.
5. Proceed to Wiring the LYNXR-I or LYNXR-ISIA section.
MOUNT
(REAR CASE)
09004-005-V0
FOR
EXTERNAL
ANTENNA
50
OHM,
MMCX
ONLY
Honeywell
GS M
GP PS
WE B
MO DE
2
MO DE
1
RS SI
7 7
2 0 P
P
R O
G
R A
M M
E
R P
O
R T
N O
T
F O
R
T E
L E
P H
O
N E
S E
R
V IC
E U
S
E !
P
R IM
A
R
Y P
O
W E
R
: 9 - 1
6 .5
V
A C
C
U
R R
E
N T
: 9
0 0
m A
P
E A
K ,
7 0
m A
S
T A
N D
B
Y
B A
T T
E R
Y
: 8
V . 3
.1
A
H r F
O
R
2 4
H
r B
A C
K U
P
F
C C
:X
X X
X X
X
X X
X X
I C
: Y
Y Y
Y Y
Y
Y Y
Y Y
OR
ARME
D
READ
Y
RECO
RD
VOLU
ME
PLAY
LIGHTS
ON
TEST
BYPASS
LIGHTS
OFF
CODE
CHIM
E
STATU
S
NO DELA
Y
FUNCTION
ESCAP
E
DELET
E
ADD
SELEC
T
AUX
0
#
7
8
9
STAY
1
2
3
4
5
6
OFF
AWAY
DESK MOUNT
(FRONT CASE)
WALL MOUNT
(FRONT CASE)
LYNXR-I / LYNXR-ISIA
Figure 1 - LYNXDM-GSM/LYNXDM-IGSM Desk/Wall Mount Installation
Wiring the LYNXR-I or LYNXR-ISIA
1. Release the LYNXR-I front case assembly from the rear case by depressing the two locking tabs at the top
of the unit with the blade of a medium size screwdriver (refer to Figure 2).
2. Once these tabs have been released, insert the screwdriver in the side of the case and release the side
locking tabs by gently twisting.
!
DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the front
assembly board.
3. Carefully disconnect the ribbon cable from the front assembly, leaving the ribbon cable connected to
the terminal block PC board (refer to Figure 2). The rear case contains the terminal block for making
wiring connections.
When installing the 4-wire communication cable, you may find it easier to make the connection at the LYNXR-I
first. The cable can then be routed through the mount’s front case.
4. Feed the 4-wire communication cable from the LYNXR-I rear case through the mount’s front case.
5. Feed the incoming wiring from the wall or desk mount rear case through the mount’s front case and into
the LYNXR-I rear case.
6. Slide the LYNXR-I onto the wall or desk mount front case locking tabs.
Step 7 only applies to wall mount installations.
7. Once the wires have been routed, the assembled wall mount front case and LYNXR-I rear case can be
hung from the wall mount rear case using three hooks on the inside of the wall mount front case and three
tabs on lower part of the wall mount’s rear case (refer to Figure 3).