Honeywell LTE-X series Скачать руководство пользователя страница 24

 

 

 

 

FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS 

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized 
changes or modifications could void the user's authority to operate the equipment.

 

CLASS B DIGITAL DEVICE STATEMENT 

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: 

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's 
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing 
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a 
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 

 

If using an indoor antenna, have a quality outdoor antenna installed. 

 

Reorient the receiving antenna until interference is reduced or eliminated. 

 

Move the radio or television receiver away from the receiver/control. 

 

Move the antenna leads away from any wire runs to the receiver/control. 

 

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. 

 

Consult the dealer or an experienced radio/TV technician for help. 

ISED CLASS B STATEMENT 

This Class B digital apparatus complies with Canadian ICES-003. 

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 

FCC / ISED STATEMENT 

This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) 
Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une 
réception indésirable. 

 

 

RF EXPOSURE 

Warning 

– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not 

be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. 

Mise en Garde 

Exposition aux Fréquences Radio : 

La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 

cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les 
procédures de produit multi transmetteur FCC et ISED.

 

 

Important Note About External Antennas 

If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.  

 

To the Installer

 

LTE-XV: The external antenna gain shall not exceed 6.94 dBi for 700 MHz, 6.00 dBi for 1700 MHz, 9.01 dBi for 1900 MHz. Under no conditions may an 
antenna gain be used that would exceed the ERP and EIRP power limits as specified in FCC Parts 22H, 24E and 27. 
LTE-XC, LTE-XA: The external antenna gain shall not exceed 6.63 dBi for 700MHz & 850MHz, 6 dBi for 1700MHz  and 8.51 dBi for 1900MHz. Under no 
conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified in FCC Parts 22H, 24E and 27, or ISED RSS-130, 
RSS-132, RSS-133, and RSS-139. 

 

 

Support and Warranty

 

For online support information, please go to: https://mywebtech.honeywell.com/ 

For the latest warranty information, go to: 
www.honeywell.com/security/hsc/resources/wa 

For patent information, see www.honeywell.com/patents 

 

MyWebTech 

 

Warranty 

 

Patents 

 
 

 

 

Ê800-23340mŠ

 

800-23340  10/17  Rev B 

 

2 Corporate Center Drive, Suite 100,  

P.O. Box 9040, Melville, NY  11747 

 2017 Honeywell International Inc.

 

www.honeywell.com/security

 

 

Содержание LTE-X series

























Отзывы: