Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 48

Страница: 48 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

10. Trouble shooting

10.1. Safety warning

As this equipment is designed and approved for use in an explosive area (intrinsic safe equipment), only

authorized service stations and the factory are allowed to repair electronic circuits.

However the customer can exchange parts and modules if the following points are observed :

1. Never open the instrument nor carry out any repair or trouble shooting in an hazardous area.

2. Use only original spare parts.

3. Work shall be done only by maintenance personnel who has an experience with intrinsically safe

equipment.

The design of the equipment is modular, i.e. in case of breakdown the customer can find out which modules

have to be replaced. The instrument consists of the following modules:

Mechanical parts

Sensing probe

Tape assembly

Display unit / electronic box

Tape cleaner

The following sections should allow to identify the defective module and to replace it.

10.2. Power supply troubles

Symptom

Origin

Action

Section

The unit does not switch

Battery too low

Change the battery

10.3

Corrosion of terminals

(battery side)

Clean the battery terminals

---

Corrosion of terminals

(display unit side)

Clean the display unit terminals

---

Switch defective

Change the display unit

10.7

The unit switches on but

stops on the message

"battery"; the buzzer

tones continuously

Battery too low

Change the battery

10.3

10.3. Transmission troubles

Symptom

Origin

Action

Section

"No Msg " is displayed

Sensor out of work or

Renew the sensor

10.5

Tape out of work

Renew the tape

10.4

"Invalid" is displayed

Sensor out of work

Renew the sensor

10.5

"Unknown" is displayed

Sensor out of work

Renew the sensor

10.5

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 48 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: