Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 41

Страница: 41 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

9.3. Tape replacement

THE REPLACEMENT OF THE TAPE DOES NOT REQUIRE TO RE-CALIBRATE THE TEMPERATURE.

Follow the different sequences as described below. The Figure 13-1 : general assembly, list of the main

spare parts can also help.

9.3.1. Disconnecting the tape from the
sensor

Follow the instructions of section 10.4 "Sensing

probe replacement".

9.3.2. Disconnecting the tape from the
electronic box

−

Unscrew with the 2.5 Allen key the 2 screws

(A) of the battery holder and pull it out as

shown on Figure 10-4.

−

Unscrew with the 2.5 Allen key the 4 screws

(B) of the display unit and pull it gently out as

shown on Figure 10-4.

−

Disconnect the connecting plug (C) as shown

on Figure 10-5 and remove the display unit.

−

Unscrew with the 2.5 Allen key the tape holder

(G) by removing the 2 screws (F) and the

grounding cable (D) as shown on Figure 10-5.

Do not loose the 2 remaining screws that

secure the reel axle.

(A)

(B)

Figure 10-4

(D) grounding cable of tape

(E) black oversleeve of tape

(G) tape holder

(H) tape

(I) securing screw

(F) securing screw

Figure 10-5

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 41 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: