Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 40

Страница: 40 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

9.2. Battery replacement

Warning : change the battery only in a non hazardous area.

−

Unscrew the 2 screws of the battery holder using the 2,5 mm Hex Allen key which is located on the

carrying case. See .

−

Pull it gently out.

−

Change the battery (one-way only device). See Figure 10-4.

−

Push the battery holder back in its housing (one-way only).

−

Tighten the 2 screws. Nota: to prevent gripping risks, we recommend adding lubricating paste on screws.

Only following batteries are approved:

Duracell / Procell MN1604 (6LR61)

Duracell 9V Industrial (6LF22)

Energizer Max (6LR61)

Disposing of general purpose & Alkaline batteries

Disposal should be in accordance with national and local regulations. Do not incinerate for disposal except in

a controlled incinerator

. .

Due to concerns about mercury in the municipal solid waste stream, Duracell / Procell alkaline batteries used

are composed primarily of common metals—steel, zinc, and manganese—and do not pose a health or

environmental risk during normal use or disposal.

Caution:

Do not throw batteries in rubbish; dispose them in a recycling bin.

one-way only device

Figure 10-4

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 40 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: