manualshive.com logo in svg

Honeywell FF-SRS5988, Инструкция по эксплуатации, Страница: 12 / 13

Поделиться
Скачать
Honeywell FF-SRS5988 Скачать руководство пользователя страница 12

12

107018-04 EN FR26 GLO 1198 Printed in Germany

FIG. 15.  FF-SRS5988 TROUBLESHOOTING FLOW DIAGRAM (PAGE 3 OF 3)

Reconnect S11

(and S21).

Reconnect S11 and

S21.  Correct/

replace the external

sensor(s), wiring,

supply voltage, etc.

Yes

No

Safety module has

failed.  Replace the

module

.

Are two channel inputs

selected?

Disconnect S11. Is input

channel one closed ? Also, is

there less than 68 Ohms and

more than 21Vdc between

S12/A4? Disconnect S21. Is

input channel two closed?
Also, is there less than 68

Ohms between S21/S23 and

more than 21 Vdc between

S22/A3 ?

Disconnect S11 and

ensure input channel

one is closed, less

than 68 Ohms

between S11/S12 and

more than 21 Vdc

between S12/A4.

No

No

Yes to all

questions

Yes

Reconnect S11.

Correct/replace the

external sensor(s),

wiring, supply

voltage, etc.

From

Fig. 14

Go to

Page 2

- Ensure channel 1 is connected

between S11/S12

- Ensure channel 2 is connected

between S21/S23

- Ensure jumper is set between

S11/S22

- Ensure jumper is set

between S12/S22

- Ensure jumper is set

between S21/S23

Содержание FF-SRS5988














Отзывы:

Нет отзывов