Honeywell FF-SB12 Series Скачать руководство пользователя страница 48

Страница: 48 / 70

107062-12 EN FR26 GLO 501 Printed in France

IMPROPER INSTALLATION OF FF-SB SERIES LIGHT CURTAIN

Use figure 3-6 wiring diagram to ensure external relay monitoring by the interface.

Failure to comply with these instructions could result in death or serious injury.

IMPROPER SYSTEM PERFORMANCE

Ensure independent stop circuit safety relays have mechanically linked contacts that prevent contact
overlapping in the event of a welded contact.

Failure to comply with these instructions could result in death or serious injury.

Figure 3-6 Wiring Diagram to replace Original Version FF-SB Series configuration with CE Version

of FF-SB Series configuration (except FF-SB12R02)

B4
B5

Not Connected

ARC SUPPRESSOR

220 ohm + 0.22 µF

EARTH

GROUND

(Emitter and Receiver

must be grounded

for proper operation)

POWER

NEUTRAL

SUPPLY VOLTAGE

Cycle Start

MACHINE CONTROL

SUPPLY VOLTAGE

EARTH

GROUND

(Emitter and Receiver

must be grounded

for proper operation)

NEUTRAL

SUPPLY VOLTAGE

INTERNAL FUSE

0,5 AMP

EMITTER AND
RECEIVER

SCREW ON

FF-SB12, FF-SB14

FF-SB15

Additional output

channel, may be

used to annunciate

to PLC

HOT

NEUTRAL

RECEIVER

Jumper Link position
on the Receiver
Power Board (factory
setting)

*Two arc suppressors are provided with the light curtain.

The cycle-start push-button is the normal push-button used to start the machine cycle and not an additional
button for the operator.

Содержание FF-SB12 Series







































































Результаты поиска

Содержание FF-SB12 Series

Отзывы:

Похожие инструкции для FF-SB12 Series

Бренды по названию

Популярные бренды

Honeywell FF-SB12 Series, Руководство по установке

Результаты поиска

Содержание FF-SB12 Series

Отзывы:

Похожие инструкции для FF-SB12 Series

Бренды по названию

Популярные бренды