manualshive.com logo in svg

Honeywell Dolphin Power Tools, Руководство пользователя

Поделиться
Скачать
Honeywell Dolphin Power Tools Скачать руководство пользователя страница 81

5 - 5

SendMode

Specifies the method to use when sending 
the decoded message to the foreground 
application.

Note: This setting affects only the decoded 

message; the prefix and suffix are 
always sent using the virtual key 
method to allow navigational 
functionality.

Note: This key does not appear in the 

ScanWedge.exm file for the Dolphin 
6100/6500/7600.

0

0=Virtual key method: each 

character is sent as a virtual 
keystroke. This method works 
well with almost any Windows 
Mobile or Windows CE 
application. 

1=Direct Text method: the decoded 

message is sent as text directly 
to the window that has the 
keyboard focus in the foreground 
application. This method is faster 
than the virtual key and supports 
barcodes with ASCII characters 
between 1 and 255 but works 

only

 if the foreground application 

uses standard Window’s Edit 
controls for user input.

2=Virtual Key (safe) method: each 

character is sent as a virtual 
keystroke using 
PostKeybdMessage(). 
This method only support bar 
codes containing ASCII 
characters and does not support 
VKMapping. This method only 
generates WM_CHAR 
messages, it does not generate 
WM_KEYDOWN and 
WM_KEYUP messages.

GoodScanWav

Specifies a .wav file played on the 
completion of a successful decode/data 
reception. 

Empty

Empty=No .wav file is specified. 

The default beep or sound is 
played. Use the 

Sound

 (page 5-

3) key to enable and disable all 
audio notification. 

X=The path to the specific .wav file 

you want played for either option. 
The .wav files should be 8-bit, 
11KHz, mono, and PCM. 

BadScanWav

Specifies a .wav file played for an 
unsuccessful decode/data reception. 

Empty

Settings Section

The Settings section determines how ScanWedge interprets data from the decoder, serial port, and IrDA 
interface.

0 = Disable    1 = Enable

Settings Section 
Key

Description

Default 
Value

Available Values

Содержание Dolphin Power Tools

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды