Honeywell DCS19W Скачать руководство пользователя страница 36

Страница: 36 / 84

Changing the Wake Area Sensitivity Level (Photocell LED Range Adjust)

The MS2400 Series bar code scanner wake area sensitivity level can be set to the end users preference by

scanning one of the Photocell Sensitivity adjustment bar codes below.

³ 2 2 1 2 0 0

³ 2 2 1 2 1 0

³ 2 2 1 2 2 0

³ 2 2 1 2 3 0

MS2400 Series Bar Code Scanner Default Setting

This feature enables the MS24xx to be at max

sensitivity or far sensing for the wake up photo

transistor.

* This is the default setting.

This feature enables the MS24xx to be at a

medium 1 sensitivity or medium sensing for

the wake up photo transistor.

This feature enables the MS24xx to be at a

low sensitivity or low sensing for the wake up

photo transistor.

This feature enables the MS24xx to be at the

lowest sensitivity (close only) for the wake up

photo transistor.

*Max Photocell

Sensitivity

Medium Photocell

Sensitivity

Low Photocell

Sensitivity

Min Photocell

Sensitivity

Содержание DCS19W





















































































Результаты поиска

Содержание DCS19W

Отзывы:

Похожие инструкции для DCS19W

Бренды по названию

Популярные бренды

Honeywell DCS19W, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DCS19W

Отзывы:

Похожие инструкции для DCS19W

Бренды по названию

Популярные бренды