Honeywell DCP 250 Скачать руководство пользователя страница 10

Страница: 10 / 16

Global Technical Assistance Center

Page 10

Segment Hold

Release Type

*Recorder Version

Only

Time to

Repeat

Sequence

Hold Release

Time

Loop 1

Auto-Hold

Type

None

(No Auto-Hold)

Above Setpoint

(Hold if Auto-Hold Band value is exceeded)

Below Setpoint

(Hold if Auto-Hold Band value is exceeded)

Band

(Hold if Auto-Hold Band value is exceeded, either above

or below)

Loop 1

Auto-Hold

Band Value

Value beyond the Profile is held, based on Auto Hold Type

Loop 2

Auto-Hold

Type

*Two Loop Option

None

(No Auto-Hold)

Above Setpoint

(Hold if Auto-Hold Band value is exceeded)

Below Setpoint

(Hold if Auto-Hold Band value is exceeded)

Band

(Hold if Auto-Hold Band value is exceeded, either above

or below)

Loop 2

Auto-Hold

Band Value

*Two Loop Option

Value beyond the Profile is held, based on Auto Hold Type

Operator/Digital

(No Auto-Hold)

Time of Day

(Hold if Auto-Hold Band value is exceeded)

Time of day when a Hold Segment will release if the Release
Type is Time of Day.

Number of Time the entire sequence of Profiles should run, if
the last segment is Repeat Sequence Then End.

Segment End

Type

Control Outputs off

(Caution this will stop all control)

Maintain Last Profile Setpoint

Use Controller Setpoint

Select profile

to Join

If Final segment is set to Join, Choose a profile to Join to.

Event n

Events 1 to 5 can be active during this segment.

Содержание DCP 250

















Результаты поиска

Содержание DCP 250

Отзывы:

Honeywell DCP 250, Часто задаваемые вопросы, Страница: 10 / 16

Результаты поиска

Содержание DCP 250

Отзывы: