Honeywell CZ-2104E, Инструкция пользователя

Страница: 2 / 28

IMPORTANT SAFETY
INSTRUCTIONS
1. Read all instructions before using heater.
2. Only connect the appliance to single phase AC sup-
ply of the voltage specified on the rating plate.
3. This appliance complies with EMC directive
89/336/EEC regarding radio and T.V. interference.
4. Keep combustible materials such as furniture, cush-
ions, bedding, papers, clothes and curtains at least
90 cm (3 feet) from the heater.
5. Extreme caution is necessary when any heater is
used by or near children.
6. Always unplug the heater when not in use. Do not
pull at the flex when disconnecting it.
7. Do not cover! If covered, there is a risk of over-
heating.
8. Do not use this heater in the immediate surroundings
of a bath, a shower or a swimming pool.
9. This heater must not be located immediately below
an electrical socket.
10. If the supply flex of this appliance is damaged it must
only be replaced by a repair shop appointed by the
manufacturer because special purpose tools are
required.
11. Keep this heater clean. DO NOT allow objects to
enter any ventilation or exhaust opening as this may
cause electric shock, or fire or damage to the heater.
OPERATION
TO OPERATE THE HEATER:
• Place the heater on a firm, level and open surface
free from obstructions. DO NOT use on an unstable
surface such as bedding or deep carpeting.
• With the Power knob in the OFF ( ) position, plug
in the heater.
• Turn the Thermostat control clockwise all the way to
the HIGH ( ) setting.
• To operate the heater, push in
the Power knob while turning it
clockwise to the desired position
(Figure 1). The power light will
illuminate. Using this feature will
help ensure that the heater can not be turned on
accidentally.
• When the room reaches a comfortable temperature,
slowly turn the Thermostat control anticlockwise until
the heater goes off. This is the point at which the
Thermostat setting equals the room temperature. At
this setting, the Thermostat will automatically turn
the heater on and off to maintain this selected
temperature.
• Push in and turn the Power knob to OFF ( ) and
unplug the heater when you are finished using it.
FAN OPERATION
• Turn the Power knob to FAN ( ) and turn the
Thermostat knob to its highest setting to use the unit
as an air circulator without heat.
NOTE: PROLONGED USE OF THE FAN DURING
THE SUMMER SEASON IS NOT ADVISABLE.
SAFETY FEATURES
• This heater has a caution light which indicates that
parts of the heater are excessively hot. DO NOT
operate the heater while the caution light is on, if the
caution light goes on, turn the heater off immediately
and make sure that no objects are on or touching the
heater. If you find an obstruction, remove it and wait
at least 10 minutes for the heater to cool before try-
ing to restart it. If the caution light is still on, see war-
ranty for instructions.
TIP-OVER SWITCH
• The heater is equipped with an automatic tip-over
switch that will disable the heater if it is accidentally
tipped over.
IF YOUR HEATER FAILS TO OPERATE:
• Check for and remove any obstructions, or if the
heater has been tipped over, set it upright. Be sure it
is plugged in and that the electrical socket is work-
ing.
• Make sure that the Thermostat is not set too low.
With the Power knob set to a heat setting, turn the
Thermostat up (clockwise) until the heater restarts.
• If the heater still won’t start see warranty for
instructions.
CLEANING
We recommend that the heater be cleaned at least once
a month.
• Turn the heater OFF ( ) and unplug it. Allow it to
cool.
• Use a dry cloth to just clean ONLY the external
surfaces of the heater. DO NOT USE WATER.
ENGLISH ENGLISH
Fig. 1