Honeywell CP-600E Скачать руководство пользователя страница 5

Страница: 5 / 20

WEB-600E AND CP-600E NETWORK CONTROLLERS

62-0433—01

Removing and Replacing the Cover

You must remove the controller’s cover to install any option cards, or to install (or replace) the optional NiMH backup battery. The

cover snaps onto the base with four plastic end tabs—two on each end.

Fig. 2. Press in four tabs on end to remove cover.

NOTE: If accessory modules are plugged into the con-

troller, you may need to slide them away from the

unit to get to the end cover tabs.

• To remove the cover, press in the tabs on both ends of the

unit, and carefully lift it off.

• To replace the cover, orient it so the cutout area for comm

ports is correct, then push inwards to snap in place.

Board Layout

Figure 3 shows the location of LEDs, option slots, and other features of the WEB-600E controller with cover removed. For a side

view of communications ports and other features, see Fig. 6.

Fig. 3. WEB-600E controller main board layout details.

The controller ships with onboard static RAM (SRAM) that can provide station backup during power loss, and also has two (2)

open option card slots for a variety of available option cards. For details, see “About Expansion Options” on page 5 below, and

also “About Backup Configurations” on page 13.

ABOUT EXPANSION OPTIONS

The controller provides for

field-installable

expansion using

these types of options:

•

Option cards

— Install on connectors on the controller’s

base board. See “About Option Cards” on page 5.

•

Accessory modules

— To “chain” on the controller’s 20-pin

connector. See “About Accessory Modules” on page 7.

About Option Cards

The WEB-600E has two (2) available option slots for option

cards designed for use with WEB controllers. Each slot has a

30-pin connector. Installing an option card is recommended

before mounting the unit. See “Installing an Option Card” on

page 7.

COVER

PRESS

TABS IN

COVER

LIFTED

AWAY

M33915

COVER TABS

(2 EACH END)

EARTH GROUND

SPADE LUG

NORMAL
SERIAL SHELL

OPTION

SLOT 2

COM 1

COM 2

SERIAL PORT LEDS ON BOTTOM BOARD, REMOVE COVER TO SEE:

LAN2

(SEC)

LAN1

(PRI)

BEAT

STATUS

STATUS LEDS (VISIBLE WITH COVER ON):

BRACKET FOR

OPTIONAL

NIMH BACKUP

BATTERY

OPTION SLOT

CONNECTORS

OPTION SLOT 1

20-PIN

CONNECTOR

(I/O AND

POWER

MODULES)

MODE JUMPER

(FOR SERIAL

SHELL ACCESS)

SECONDARY

ETHERNET

(RJ-45) LAN2

(TOP BOARD)

RS-232

(DB-9)

COM1

(BOTTOM

BOARD)

BARREL POWER

CONNECTOR FOR

WALL MOUNTED

POWER MODULE

(NPB-WPM-US)

PRIMARY

ETHERNET

(RJ-45) LAN1

(TOP BOARD)

RS-485

(3-POS.)

COM2

(BOTTOM

BOARD)

NPM6E PROCESSOR

MODULE WITH

INTEGRAL SRAM

M33918

Содержание CP-600E





















Результаты поиска

Содержание CP-600E

Отзывы:

Похожие инструкции для CP-600E

Бренды по названию

Популярные бренды

Honeywell CP-600E, Руководство пользователя

Результаты поиска

Содержание CP-600E

Отзывы:

Похожие инструкции для CP-600E

Бренды по названию

Популярные бренды