background image

CABLING

EN1B-0022 IE10 R0717

12

Cable lengths and cross sectional areas

1.E.g. for 0-10 VDC input, NTC20K, PT1000, dry 
contact, 0-10 VDC output.

MS/TP cable specification

Use Belden 9841 or Equivalent cable with the following 
specifications

An MSTP EIA-485 network shall use shielded, twisted-pair 
cable with characteristic impedance between 100 and 130 
ohms.

Distributed capacitance between conductors shall be less 
than 100 pF per meter (30 pF per foot).

Distributed capacitance between conductors and shield 
shall be less that 200 pF per meter (60 pF per foot).

Foil or braided shields are acceptable.

The maximum recommended length of an MS/TP segment 
is 1000 meters.

Sylk Bus cable specification

Polarity insensitive

Can use daisy chain wiring for multiple Sylk devices. If 
wire size is too thick for two wires in the terminal, use 
pigtails.

Connection drawings

This section describes example connection drawings of the

CPO-VAV2A controller with:

MS/TP bus

Sylk bus

24 VAC power, and IO connection

Signal type

Cross-sectional
Less than or 
equal to 300 Ft. 
(100m)

Less than or 
equal to 500 ft. 
(170 m)

Less than or 
equal to 1300 ft. 
(400 m)

Power 
supply (24

VAC)

Less than or 
equal to 16

AWG (Greater 
than or equal 
to 1.5 mm

2

)

Less than or 
equal to 14

AWG (Greater 
than or equal to

-

Low current 
signals 

1

Less than or equal to 20 AWG (Greater than or 
equal to 0.5 mm

2

)

Attention

The maximum length of a signal cable with 24 
VAC supply is 550 ft. (170 m). The max. length of 
a two-wire, 0-10 Vdc signal cable is 1300 ft. (400 
m). The secondary side of the transformer must 
not be connected to earth ground.

Installing a fuse on the secondary side of the 
transformer is recommended to protect the 
devices against incorrect wiring.

Recommended maximum distance

from controller to any Sylk device

Quantity 

and type of 

device

Single twisted pair, non-

shielded, stranded or solid

Standard

thermostat wire, (non-

twisted), shielded or 

nonshielded, stranded or 

solid

18-22 AWG

24 AWG

18-24 AWG

3 wall 

modules, 

any type

500 ft

(150 m)

400 ft

(120 m)

100 ft

(30 m)

Содержание ComfortPoint Open CPO-VAV2A




















Отзывы: