Honeywell CN70 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 45

background image

TITLE

Model

DOCUMENT NO.

PAGE

CN70 Service Work Instructions

CN70A,CN70E

SWICN70-000

Page

27

of

45

Installation
When reinstalling display assembly parts be careful not to gets scratches, fingerprints, dust, or other contamination
on the display surfaces. Assembly in a clean environment using some form of finger protection is required.

1. Confirm that the LCD display has two grounding pads installed as shown. If this is a new LCD display you will
need to install new grounding pads. Temporarily position the boot over the back of the LCD display and use the
cutouts in the boot to properly position the grounding pads as they are installed.

2. Position the boot in the magnesium frame. Make sure it is oriented correctly with the cutout for the touch panel
flex located down by the keyboard PCB.
3. Position the touch panel as shown and connect the touch panel flex cable.

Continued on next page…

4. Flip the touch panel over so it is now located above the keyboard PCB assembly.

Cutout in boot for
touch panel flex
cable

Connect touch
panel flex cable

Use boot as a guide to
install new grounding
pads as needed

4

«
...
25
26
27
28
29
...
»

Содержание CN70 Series














































Отзывы:

Нет отзывов

Похожие инструкции для CN70 Series

Бренд: Palm Страницы: 150

Бренд: CCV Страницы: 32

Presenter-to-Go

Бренд: InFocus Страницы: 46

Бренд: Pyle Sports Страницы: 16

Бренд: OBM Страницы: 8

Бренд: IEI Technology Страницы: 33

Бренд: IEI Technology Страницы: 74

Бренд: Intermec Страницы: 2

7600BG-122-B4EE - Hand Held Products Dolphin 7600

Бренд: Honeywell Страницы: 142

Бренд: PSC Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды