T4600 Chronotherm
®
ELECTRONIC PROGRAMMABLE LINE VOLTAGE THERMOSTAT
68-0168—3
7
M4659
AUTO MAN TEMPOR NIGHT DAY
M4658
AUTO MAN TEMPOR NIGHT DAY
Su Mo Tu We Th Fr Sa
M4662
AUTO MAN TEMPOR
M4653
AUTO MAN
AUTO
M4663
After programming the T4600, there is no need for further
adjustment during the heating season. During the summer,
use the AUTO and down (-) keys to lower and hold the
setpoint or turn off the power.
NOTE:
The battery life is shortened if the T4600 is
unpowered (with circuit breaker turned off) for long
periods of time.
Additional Questions? Call Honeywell Consumer Services:
1-800-468-1502, Monday-Friday, 7:00 a.m. to 5:30 p.m.,
Central Time.
CHECKOUT
When the thermostat is first powered or if the battery is
drained, the display shows all segments briefly:
Then it shows 00E for 15 seconds followed by a flashing
12:00 AM (midnight) to indicate that the thermostat needs to
be programmed. If the time of day program is not entered, the
thermostat controls to the default setpoint, 60
°
F (16
°
C). If the
ambient temperature is below freezing, the display does not
operate until the power supply warms up the thermostat to
the operating temperature. There will be a clicking from the
relay, indicating the thermostat is working even though the
display is not restored.
Check out the thermostat operation by simulating normal
operation as follows:
1. Press and hold the up (+) key to raise the setpoint
above the ambient room temperature, calling for heat.
The temperature degree symbol flashes and the
electric heater warms up.
2. Press and hold the down (-) key to lower the setpoint
below the ambient room temperature. The temperature
degree symbol stops flashing and the electric heater
starts to cool down.
3. To determine the appropriate setpoint, set the
temperature at 68
°
F (20
°
C). Let the system operate for
at least one hour and adjust the setting as necessary.
M4657
AUTO MAN TEMPOR NIGHT DAY
Su Mo Tu We Th Fr Sa
AM
PM
ACTIVITY
RESULT
DISPLAY
Set Cottage Programs:
CAUTION:
Before using the COTTAGE program, make
sure there are no water pipes along outside
walls, sealed in cabinets or installed in a
manner that can cause them to freeze when
the room temperature falls to 45°F (7°C).
In the COTTAGE program, the thermostat sets
back to 45°F (7°C), which is preprogrammed
and not adjustable. The DAY setback program
does not operate in the cot0 mode. The
temperature is controlled at 45°F (7°C) from
the NIGHT setback time on Sunday to the
morning recovery time on the following
Saturday.
Press the up (+) and down (-) keys to select
the desired COTTAGE program.
The display flashes cot0, indicating that the
day setback program will not operate.
Press the up (+) and down (-) keys to select
the desired COTTAGE program.
In the cot3 mode, the DAY setback program
operates on Friday, Saturday and Sunday. The
temperature is controlled at 45°F (7°C) from
the NIGHT setback time on Sunday to the
afternoon recovery time on the following
Friday.
After selecting the NORMAL or COTTAGE
program, press and release the PROG key to
enter the program.
The thermostat enters the programmed mode,
displays the room temperature and AUTO.
The up arrow indicates the comfort period; the
down arrow indicates the economy period.
TEMPORARILY OVERRIDE THE
PROGRAM
Press the up (+) and down (-) keys to
temporarily change the temperature setpoint.
The current setpoint is displayed on the first
press of the up or down key. The setpoint can
be changed by pressing the up or down keys
again. The display also flashes TEMPOR
(temporary). This temporary program override
changes back to AUTO operation when the
next program change occurs.
PERMANENTLY OVERRIDE THE
PROGRAM
Press and release the AUTO key.
MAN (manual) is displayed. The program
change remains in effect until the PROG or
AUTO key is pressed.