Honeywell CGW-MB Скачать руководство пользователя страница 139

Страница: 139 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

138

Supported Panels

Connecting to the Panels

C.2 Supported Panels

The CGW-MB supports the following panel variants:

•

•

•

•

•

•

•

•

•

NOTIFIER® European Panels (EN)

•

Silent Knight Panels

•

Triga Panels

•

VESDA® Detectors

C.3 AM Series Panels

C.3.1 Connection Options

The CLSS Gateway mainboard operates only with the AM Series fire alarm control panels
listed in the table below:

Table C.1: AM Series Panel Connection Options

Minimum Required Versions

For the Panel/CPU1: v1.0.703 | For SIB version Panel: v0.68
For the CGW-MB: 3.0.4.56

C.3.2 To Use an RS-232 Connection

Using an RS-232 cable the CGW-MB and the panel are connected.
The RS-232 port in the CLSS Gateway mainboard board is labeled as 6 in the

Figure C.2

1. On the CLSS Gateway mainboard Side

Connect to an RS-232 port of the CLSS Gateway mainboard board.

2. On the Panel Side

•

AM8200 Panels

•

AM8200 Panels

• Connect the White wire to the RX pin of the SIB 8200 board.
• Connect the Green wire to the GND pin of the SIB 8200 board.
• Connect the Brown wire to the TX pin of the SIB 8200 board.

Fire Alarm Panel Models

RS-485

UART/TTL

RS-232

USB

AM8200

Yes

1 Use the SIB 8200 board

NOTE:

The panel can be a stand alone panel or part of a network of panels.

NOTE:

Because the SIB 8200 board on the panel connects to the CLSS Gateway

mainboard, the SIB board cannot be used for printing the events.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 139 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: