Honeywell CGW-MB Скачать руководство пользователя страница 171

Страница: 171 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

170

Morley-IAS Panels

Connecting to the Panels

C.9 Morley-IAS Panels

C.9.1 Connection Options

The CLSS Gateway mainboard operates only with the Morley-IAS fire alarm control panels
listed in the table below:

Table C.7: Morley-IAS European Panel Connection Options

C.9.2 To Use an RS-232 Connection

Morley-IAS panel variants use an RS-232 connection with the CGW-MB.

1. On the CLSS Gateway mainboard Side

1. Connect the RS-232 cable with pre-formed connector to the RS-232 port of the

CLSS Gateway mainboard board.

The RS-232 port is labeled as 6 in the

Figure C.2

2. On the Panel Side

•

Morley DXc Panels

• Morley DXc Panels

In the SK1 terminal of the panel:

• Connect the White wire to the RxD+ pin.
• Connect the Green wire to the Gnd pin.
• Connect the Brown wire to the TxD+ pin.

3. Power Connection

The CLSS Gateway mainboard’s RS-232 port can receive its power either from an

external power source or from the non-resettable internal power of the panel.

Fire Alarm Panel Models

RS-485

UART/TTL

RS-232

USB

DXc

Yes

1 Use the serial communication card (P/N: 795-122) on the panel.

NOTE:

Compatible CGW-MB firmware versions: 3.0.2.30 and above.

NOTE:

In a network of panels, connect the CLSS Gateway mainboard to the master panel.

NOTE:

The external power supply must be dedicated and not shared with any other

devices.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 171 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: