background image

BACNET® FIXED FUNCTION THERMOSTAT

31-00099—01

4

APPLICATION 0 – HEAT PUMP (AIR TO AIR)

Features and Notes

• Three modes of schedule control set by AV-123 –

0 = Single point with offset during occupancy,
1 = Dual setpoint residential – wake, leave, return & sleep,
2 = Dual setpoint with offset occupancy.

• BACnet MS/TP compliant.
• English or metric units.
• Outputs are disabled if BV-2 is off.
• Disable operator access via the display to the schedule 

by setting BV-102 to off.

• Onboard schedule can be enabled or disabled (BV-40).
• Heating and cooling are disabled if the fan is off.
• Use up and down arrows on the display to force the unit 

into occupancy for four hours.

• Setpoint mode emulates residential thermostat 

operation.

• Standby mode enables power saving if no motion is 

detected while in occupancy.

• If condensation is detected, the compressor is held off 

with the optional condensate input.

• By default the economizer control is set for analog. To 

use three point floating control set a value in AV-63 
(Economizer Stroke Time).

• The economizer control requires a supply air sensor 

connected to AI-2:.

• One stage of auxiliary heating.
• Use 10K Type II Thermistor sensors for analog inputs.
• Electric heat is enabled when heating demand is > 65%.
• To configure AI-0 as a sensor set the following 

parameters.

SINGLE STAGE ELECTRIC HEAT

Inputs

AI-0:: Space Sensor or Outside Air 

Sensor (optional)

AI-2:: Supply Air Sensor (optional, 

required for economizer control)

BI-1:: PIR/Door/Window Sensor 

(optional)

BI-2:: Condensate Sensor (optional)

Outputs

BO-0:: Fan
BO-1:: Heat Pump Compressor
BO-2:: Reversing Valve
BO-3:: Electric Heat (optional)
BO-4:: Economizer Open (optional for 

floating control)

BO-5:: Economizer Close (optional for 

floating control)

AO-0:: Economizer (optional analog) 

0-10V or 4-20mA

AO-1:: Fan Speed Control (optional) 

4-20mA VFD/SCR

Note: Any I/O listed as “optional” will 

require a BV to be set. Refer to the 
sequence of operations outlined in 
the BACnet FF Thermostat System 
Engineering Guide, 31-00098.

MS/TP Network

Compr.

Rev. 

Valve

Digital

Digital

Digital

Supply 

Fan

Electric 

Heater

Digital

Space or Outside 

Temperature Sensor  

(optional)

Supply 

Temperature Sensor 

(required for economizer 
control) 

PIR/Door/Window Sensor 

(optional)

Condensate Sensor  

(optional)

Digital

BV-47 (PS)

BV-32 (Sr)

Space Temperature

Off

On

Outside Temperature

On

Off

Fan

HP Cmpr

Rev Vlv

Htg Stg 1

Econ Opn

Econ

Econ Cls

Controller Terminations     

HPH1 AP 0

GND

5

BO 0

BO 1

BO 2

BO 3

BO 4

BO 5

AO 1

G

Y1

O/B

W1

EC

EC

EC

0-10Vdc

Com

14

AO 0

C

RC

24VAC

1

24V

Com

BI/AI 1

COM

BI/AI 2

COM

BI/AI 0

Sensor *

SA Sensor

Optional 
Standby

N.C. or N.O.

Optional 

Condensate  

alarm or fail

VC

VFD /SCR

4-20ma

* Optional space or outside temperature sensor.

4-20ma

Содержание BACnet





























Отзывы: