manualshive.com logo in svg

Honeywell Aquastat L4006, Данные о продукции, Страница: 12 / 20

Поделиться
Скачать
Honeywell Aquastat L4006 Скачать руководство пользователя страница 12

L4006,7,8; L6006,7,8 AQUASTAT

®

 CONTROLLERS

60-2104—10

12

Mounting on Suction Line

1.

In cooling units with more than one suction line, place 

the sensing bulb on the common line.

2.

Make certain the bulb is at least 2 ft (0.6 m) from the 

point at which the suction line leaves the cooler. This 

prevents the outside temperature from being transmitted 

to the remote bulb through the copper tubing of the 

suction line.

3.

Place the remote sensing bulb on the side of the 

horizontal suction line between the coil and trap (not on 

the trap).

4.

Attach the sensing bulb to the suction line with clips or 

straps. (See Fig. 17).

5.

Coil the excess length of capillary tubing near the 

L6008A case.

Fig. 16. Securing remote bulb in clip

when mounting with guard bracket.

Fig. 17. Attaching remote bulb to horizontal suction line.

Mounting Surface Mount Models

The L4006H and L6006C are designed for surface mounting 

on piping or tanks. Mount the controller directly on the tank 

surface using the adjustable mounting bracket as shown in 

Fig. 18. The controller can be mounted in any position.

When mounting the L4006H or L6006C on piping, the pipe 

should be 1 in. (25 mm) diameter or larger for accurate 

temperature sensing. Remove any insulation from the pipe. 

Thoroughly scrape off all scale, rust, or paint. Mount the 

controller using adjustable bracket provided. Turn on power.

Wiring

Disconnect power supply before beginning installation to 

prevent electrical shock or equipment damage.

All wiring must comply with local codes and ordinances 

regarding wire size, type of insulation, enclosure, etc.

Figures 19 through 28 show typical hookups.

When wiring a switch equipped with a 1/4 in. (19 mm) tab 

terminal connector, use 18 AWG to 22 AWG (0.8 mm

2

 to 

0.3 mm

2

) gauge wire with an AMP Inc. part no. 2-520129-2 

fully insulated flag receptable connector or equivalent.

Fig. 18. Mounting L4006H or L6006C directly on surface.

Fig. 19. Typical gas-fired system with domestic hot water.

M8791A

SUPPORTING 

CLIP

SENSOR

M8805A

L6008A

CIRCULATOR

LOW LIMIT

CONTROLLER

CAPILLARY

REMOTE 

BULB

SUCTION

LINE

BULB CLIPS

TO SUCTION LINE

COIL

COOLER

WALL

SUCTION LINE

LEAVES 

COOLER

M8771B

ENCLOSED

SENSING BULB

PIPE

12 IN.

ADJUSTABLE

PIPE 

STRAP

AQUASTAT

CONTROLLER CASE

MOUNTING

BRACKET

®

POWER SUPPLY.  PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

USE L4006E FOR MANUAL RESET.

1

2  

M2856B

2  

L1 

(HOT)
L2

1

24 VOLT

THERMOSTAT

LOW WATER

CUTOFF

PRESSURE 

CONTROL

L4006A OR

L4007A

LOW LIMIT

AQUASTAT

CONTROLLER

GAS

VALVE

PILOTSTAT

CONTROL

®

Содержание Aquastat L4006





















Отзывы:

Нет отзывов