manualshive.com logo in svg

Honeywell APT4000PH, Руководство пользователя

Поделиться
Скачать
Honeywell APT4000PH Скачать руководство пользователя страница 41

APT4000PH

80

Relay test (manual test of contacts)

• Press 

CONF

, enter code 5557

The relays are frozen. This state is indicated in the display.
The 4 digits in the display correspond to the 4 relays (as on
terminal plate):
1st digit: R1
2nd digit: R2
3rd digit: AL
4th digit: CLN
Function test using arrow keys – see left column. 
When exiting the function (

ENTER

), the relays are set corre-

sponding to the measured value.

Select a relay

Specify current at output 1

• Press 

CONF

, enter code 5555

The current indicated in the main display for output 1 can
be edited.
Select with 

key, 

edit number with 

key, 

proceed with 

ENTER

The actually measured current is shown in the secondary
display. The APT4000PH is in Hold mode.
Press 

ENTER

to return to measurement (Hold remains

active for another 20 sec).

Diagnostics functions

These functions are used for testing the connected peripherals.

Display

Action / Remarks

Specify current at output 2

• Press 

CONF

, enter code 5556

The current indicated in the main display for output 2 can
be edited.
Select with 

key, 

edit number with 

key, 

proceed with 

ENTER

The actually measured current is shown in the secondary
display. The APT4000PH is in Hold mode. 
Press 

ENTER

to return to measurement.

Test 0/1

Return to
measurement

81

The arrows indi-
cate which relay
(valve) is active:

Controller 
characteristic 

+100 %

-100 %

Relay 2 active
(Meas. value >
setpoint)

Relay 1 active
(Meas. value <
setpoint)

Setpoint

Controller output

Momentary controller output (adjusted value has not been
stored yet)

Controller test (manual specification of controller
output)

• Press 

CONF

, enter code 5559

After function activation “Ctrl” is displayed for approx.
3 sec. 
With controller turned off, “OFF” is displayed in addition,
then return to measuring mode.
The function is used to start up control loops or check the
actuators. 
For bumpless changeover to automatic operation 
(exiting this function), configure an I-action component
(reset time).

Specify value:
Select with 

key, 

edit number with 

key, 

proceed with 

ENTER

APT4000PH is in Hold mode.
Press 

ENTER

to return to measurement 

(Hold remains active for another 20 sec).

Controller output -100 to 0 %:

Relay 2 active

Controller output 0 to +100 %:

Relay 1 active

Display

Action / Remarks

Содержание APT4000PH




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды