Honeywell 145*g1D Скачать руководство пользователя страница 86

Страница: 86 / 206

4 - 16

Video Reverse

Video Reverse is used to allow the scanner to read bar codes that are inverted. The

Video Reverse Off

bar code below is an

example of this type of bar code. Scan

Video Reverse Only

to read

only

inverted bar codes. Scan

Video Reverse and Stan-

dard Bar Codes

to read both types of codes.

Note: After scanning

Video Reverse Only

menu bar codes cannot be read. You must scan

Video Reverse Off

Video

Reverse and Standard Bar Codes

in order to read menu bar codes.

Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.

Working Orientation

Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside
down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner.

Default = Upright.

Video Reverse Only

Video Reverse and Standard Bar

Codes

* Video Reverse Off

Upright:

Vertical, Top to Bottom:

(Rotate CW 90°)

Upside Down:

Vertical, Bottom to Top:

(Rotate CCW 90°)

Содержание 145*g1D















































































































































































































Результаты поиска

Содержание 145*g1D

Отзывы:

Honeywell 145*g1D, Руководство пользователя, Страница: 86 / 206

Результаты поиска

Содержание 145*g1D

Отзывы: