manualshive.com logo in svg

Honeywell 145*g1D, Руководство пользователя, Страница: 20 / 206

Поделиться
Скачать
Honeywell 145*g1D Скачать руководство пользователя страница 20

2 - 2

RS485

Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface.

Note: After scanning one of these codes, you must power cycle the cash register.

Each bar code above also programs the following suffixes for each symbology:

* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface

RS485 Packet Mode

The following selection allows you to break up large bar code data into smaller packets on an IBM POS terminal.  To break 
up large bar codes into small packets, scan the Packet Mode On bar code below.  Scan the Packet Mode Off bar code if you 

want large bar code data to be sent to the host in a single chunk.  

Default = Packet Mode Off.

Symbology

Suffix

Symbology

Suffix

EAN 8

0C

Code 39

00  0A  0B

EAN 13

16

Interleaved 2 of 5

00  0D  0B

UPC A

0D

Code 128 *

00  0A  0B

UPC E

0A

Code 128 **

00  18  0B

MaxiCode

00  2F  0B

IBM Port 5B Interface

IBM Port 9B 

HHBCR-1 Interface

IBM Port 17 Interface

IBM Port 9B

HHBCR-2 Interface

* Packet Mode Off

Packet Mode On

Содержание 145*g1D















































































































































































































Отзывы:

Нет отзывов