4
3
2
1
12
11
10
9
8
7
6
5
4
3
2
1
14
13
Z8
GND
Z7
Z6
GND
Z5
Z4
GND
Z3
Z2
GND
Z1
GND
Z9
GND
GND
15.
5V IN
5800C2W-001-V1
12V
AUX
+
EOLR
RED
Zone Calibration Button
Not Used
BLACK
-
+
Integral
Fuse
(+)
To Backup Battery,
Battery must read a
minimum 9.5VDC
before the charging
circuit will initiate
Refer to LED Functions
SW1
SW2
OBSERVE
POLARITY
Provides 11.2VDC ±15% @ 100mA
to supply PIR motion, or glassbreak
sensors.
(Minimum voltage is 10.5VDC)
Zone 1 of 9
shown wired
IMPORTANT:
The first battery test occurs 1 hour after power up. To quickly verify a good backup battery,
unplug and then plug back in the power supply; the system will perform a battery test within 1 minute
NOTES:
•
All zones that are used MUST
have an EOL resistor.
•
EOL resistor values must be
from 1k to 10k ohms. (Nine
2.2k ohm resistors are
included for those panels not
using any resistors.)
•
If the existing installation
zones have EOL resistors
(from 1k to 10k ohms) they
may remain.
•
For a NC loop without an EOL
resistor, you must add one in
series with the loop. Preferably
it should be located at the end
of the loop furthest away from
the control panel for proper
supervision.
•
For a NO loop without an EOL
resistor, you must add one in
parallel (across) the loop.
Preferably it should be located
at the end of the loop furthest
away from the control panel for
proper supervision.
SPECIFICATIONS
Dimensions
Length 7.0 in. (178mm), Width 4.5 in. (114mm) ,Depth 1.5 in. (38mm)
Mounting Hardware
Double stick tape and screws included.
Operating Temperature
+14 to +140°F (– 10 to +60°C)
Humidity
95% RH Max.
Transmission Range
Up to 300ft. (91 meters)
Operating Voltage
Supplied by plug-in transformer 15.5VDC (± 5%) @ 1A (P/N: 300-07052, or 300-07102 Canada)
Battery Backup
Use 12V, 4Ah battery such as Resideo 467, Yuasa NP4-12, Casil CA1240 or equivalent. Provides 4 hours of backup.
Battery is to be located in the existing control panel. DO NOT use batteries of larger capacity.
Tamper Detection
Activated when the cover is removed.
5800C2W Supervision
•
low battery
•
backup battery power
•
each enrolled zone transmits a supervisory message every 72 minutes
LED Status Indicators
(The input power indicator is viewable
through the enclosure cover.)
•
input power
•
backup power
•
wireless transmission
Input Zones
(9 hardwired)
All zones that are used must have an EOL resistor. (Refer to the back page for detailed information.)
Auxiliary Output
(12VAUX)
Provides 11.2VDC ±15% @ 100mA to supply PIR motion, or glassbreak sensors.
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105. The Class B Digital Device
statement can be viewed at:
https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1)
Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception
indésirable.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747,
Ph: 516-577-2000
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human health.
Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited
SUPPORT & WARRANTY INFORMATION
For the latest documentation and online support information, please go to:
www.resideo.com
For the latest warranty information, please go to:
https://www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product manufactured by Resideo and its affiliates.
Ê800-15422ESŠ
800-15422E 9/13 Rev. E
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
LED
Function
Note
: LEDs are shown as they appear on the circuit board.
#1
Red (blinking) – Module needs calibrating.
Green – Module is calibrated.
#2
Green – DC power (15.5VDC, ± 5%) from the plug-in transformer is present.
Red – DC power is NOT present.
(Viewable through the enclosure cover.)
#3
Yellow – Low battery or No battery.
When the battery voltage drops to 11.2VDC, a low battery message is sent to the control panel and LED 3 turns yellow.
When the battery voltage drops to 9.5VDC, the battery is disconnected. The battery will not connect again until AC is restored.
#4
Green (blinking) – RF signal transmission.
