Honda NT650 Скачать руководство пользователя страница 2

Страница: 2 / 97

IMPORTANT NOTICE



OPERATOR AND PASSENGER

This motorcycle is designed to carry the operator and one passenger. Never exceed the
maximum weight capacity as shown on the tire information label.



ON-ROAD USE

This motorcycle is not equipped with a spark arrester and is designed to be used only on
the road. Operation in forest, brush or grass covered areas may be illegal. Obey local laws
and regulations.



READ THIS OWNER'S MANUAL CAREFULLY

Pay special attention to statements preceded by the following words:

⚠

DANGER

Indicates severe personal injury or death will result if instructions are not followed.

⚠

WARNING

Indicates a strong possibility of severe personal injury or death if instructions are not
followed.

CAUTION:

Indicates a possibility of personal injury or equipment damage if instructions are not
followed.

NOTE

Gives helpful information.

This manual should be considered a permanent part of the motorcycle and should remain with
the motorcycle when resold.

Содержание NT650


































































































Результаты поиска

Содержание NT650

Отзывы:

Похожие инструкции для NT650

Бренды по названию

Популярные бренды

Honda NT650, Руководство пользователя

Результаты поиска

Содержание NT650

Отзывы:

Похожие инструкции для NT650

Бренды по названию

Популярные бренды