background image

4

INITIAL SNOW BLOWER SETUP

List of Parts

With help from an assistant, carefully remove the snow blower and 
loose parts from the carton and compare the loose parts against the 
following list. Contact the authorized Honda dealer from whom you 
purchased the snow blower if any of the loose parts shown are not 
included with your snow blower.

Tool Kit

Add Engine Oil

The snow blower is shipped 

WITHOUT OIL

 in the engine.

1. With the snow blower on a level surface, remove the oil filler 

cap/dipstick.

2. Add oil from the included bottles of oil into the oil filler opening until 

it reaches the upper limit mark on the dipstick. Do not thread the 
dipstick in when checking the oil level.

All Honda engines are run at the factory prior to packaging. Most of 
the oil is removed prior to shipment; however, some oil remains in 
the engine. The amount of oil left in the engine varies.

3. If you don’t use the supplied oil, add enough recommended oil 

(

page 16

) to bring the oil level to the upper limit mark on the 

dipstick. Do not thread the dipstick in when checking the oil level.

4.

Do not overfill the engine with oil

. After filling the engine with oil, 

screw the filler cap/dipstick in and remove the hang tag near the 
recoil starter grip that says “

The engine has no oil

.”

Please Register Your Snow Blower

Please take a few minutes and register your purchase with Honda. 
You can register by:

• Completing and mailing the registration card included with this 

owner’s manual

• Scanning the QR code to the right and completing 

the online form

• Going online to 

powerequipment.honda.com

 and 

clicking on Product Registration

Before Using Your Snow Blower

All snow blower operators must read the following sections:

• FOR YOUR SAFETY 

(

page 2

)

• BEFORE EACH OPERATION 

(

page 5

)

• OPERATION 

(

page 6

)

• MAINTENANCE SCHEDULE 

(

page 15

)

Ref
No.

Description

Qty.

Tool kit (see below)

1

Bottle of oil (16 oz)

2

Skid shoes (wheel-type 
models) (see 

page 17

)

2

Ignition key

2

Owner’s manual 

1

 

!

"

#

SPARK PLUG WRENCH

WRENCH HANDLE

14×17 mm WRENCH

10×12 mm WRENCH

6 mm SELF 

LOCKNUTS (6)

SHEAR BOLTS (4)

TOOL BAG

CARRIAGE SHEAR

BOLTS (2)

FUSE 5 A

(electric-starter 

models)

OIL FILLER 
CAP

UPPER LIMIT

Содержание HSS1332A

































Отзывы: