background image

SAFETY PRECAUTIONS 

Before operating the sweeper for the first time, please review the IMPORTANT SAFETY INFORMATION 
beginning on page 3 and the previous chapter, titled BEFORE OPERATION. 

Even 

if you have operated other sweepers, take time to become familiar with how this sweeper works, 

and practice in a safe area until you build up your skills. 

For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your 

sweeper’s engine exhaust contains poisonous carbon monoxide gas which can collect rapidly in an 
enclosed area and cause illness or death. 

The following precautions are suggested to help prevent accidents. A careful operator is the best 
operator. Most accidents can be avoided by observing certain precautions. Read the following 
precautions before operating the sweeper to help prevent accidents. Equipment should be operated only 
by those who are responsible and instructed to do 

so. 

Do not allow anyone to ride on the sweeper. 

Keep hands, feet, face, hair and clothing away from rotating parts. 

Be aware of the sweeper discharge direction. 

Do 

not point discharge at anyone. 

Always move the blade control lever OFF, shut the engine OFF, remove the ignition key, and wait for 
all moving parts to stop before leaving the operator’s position, leaving the sweeper unattended or 

inspecting the sweeper. 

Do 

not operate the sweeper with children, pets or others nearby. 

Be sure the area is clear of other people before operation. Stop the machine 

if anyone enters the area. 

Watch out for traffic when operating near or crossing roadways. Slow down before turning and 
approach blind corners cautiously. 

embankments and other potentially dangerous areas. 

Always observe the area ahead. Avoid obstacles and stay away from holes, ditches, soft or steep 

Wet surfaces reduce traction and stability. Always maintain proper traction. 

Children 

Accidents can occur if the operator is not alert to the presence of  children. Children are often attracted to 
the machine and the sweeping activity. Never assume that children will remain where you last saw them. 

Keep children out of the work area and under the watchful eye of another responsible adult. 

Be alert and turn off the machine if children enter the area. 

FS7054 FRONT SWEEPER 

Содержание FS7054









































Отзывы: