Honda FS7054 Скачать руководство пользователя страница 10

BEFORE OPERATION 

GENERAL 

The operator presence levers are part of the interlock system. If the interlock system is not working 

properly, repair it before operating the sweeper. 

The engine will shut off when both power unit operator presence levers are released, 

if the speed control 

levers are out of neutral or the blade control lever is ON. 

For your safety, and to prolong the service life of your equipment, always inspect the sweeper before 

each use. Refer to the MAINTENANCE SCHEDULE on page 17. 

Perform the Before Mowing checks listed in the power unit owner’s manual. 

Cold 

Weather 

It may be necessary to install any or all of the following options depending on your particular power unit 
and your operating conditions. 

Headlight Kit. 

Agricultural Tire Kit. 

Engine Cold Weather Kit. 

Carburetor Anti-Icing Kit (HRC7013K1 only). 
Hydraulic Drive Release. 
Cab Kit. 

Refer to page 36 for option details. 

Refer to the power unit owner’s manual for correct oil viscosity selection. 

CHECK SWEEPING AREA 

For your safety and the safety of others, always inspect the area before sweeping. 

 Objects 

Anything which can be picked up by the broom and thrown is a potential hazard to you and others. 
Always remove any large debris from the sweeping area. 

Remove motor vehicles or other objects from the sweeping area to prevent them from getting damaged. 

People 

and 

Pets 

People and animals near the sweeping area can move into your path or into a position where they could 

be struck by thrown objects. Clear the area of people and pets, especially children. Their safety is your 
responsibility. 

PROTECTIVE 

CLOTHING 

Be sure to wear protective clothing such as long pants and eye protection which can lower your risk of 
injury from thrown objects.  Wear footwear that protects your feet and won’t let you slip if you sweep on 
uneven ground. Wear hearing protection to protect your hearing. 

Do 

not wear loose fitting clothing, jewelry, scarves, ties, etc., which may get caught in moving parts. Tie 

up or restrain long hair. 

Wear a dust mask when sweeping in dusty conditions. 

FS7054 FRONT SWEEPER

Содержание FS7054









































Отзывы: