Honda EU2000i Companion Скачать руководство пользователя страница 49

Страница: 49 / 75

−

0.024

0.028 in

(0.60

0.70 mm)

SEALING WASHER

After the spark plug is seated, tighten with a spark plug wrench to
compress the washer.

If installing a new spark plug, tighten 1/2 turn after the spark plug
seats to compress the washer. If reinstalling a used spark plug,
tighten 1/8

1/4 turn after the spark plug seats to compress the

washer.

Measure the spark plug electrode gap with a wire-type feeler gauge.
Correct the gap, if necessary, by carefully bending the side electrode.

Check that the spark plug sealing washer is in good condition, and
thread the spark plug in by hand to prevent cross-threading.

A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the cylinder
head.

Reinstall the spark plug cap on the spark plug securely.

Reinstall the spark plug maintenance cover.

0.024

0.028 in (0.60

0.70 mm)

Visually inspect the spark plug. Replace it if the electrodes are worn
or if the insulator is cracked, chipped, or fouled.

10.

The gap should be:

06/12/21 09:21:02 31Z07602_048

Содержание EU2000i Companion












































































Результаты поиска

Содержание EU2000i Companion

Отзывы:

Похожие инструкции для EU2000i Companion

Бренды по названию

Популярные бренды

Honda EU2000i Companion, Руководство пользователя

Результаты поиска

Содержание EU2000i Companion

Отзывы:

Похожие инструкции для EU2000i Companion

Бренды по названию

Популярные бренды