Honda EU 1000i Скачать руководство пользователя

Страница: 82 / 92

WITHOUT OIL

Do not overfill the engine with oil.

ENGINE OIL

INITIAL USE INSTRUCTIONS

COVER SCREW

OIL FILLER CAP/DIPSTICK

MAINTENANCE COVER

The generator is shipped

in the engine.

Reinstall the maintenance cover.

With the generator in a level position, remove the oil filler cap/
dipstick.

Add enough SAE 10W-30 API service category SJ or later (or
equivalent) oil to bring the oil level to the upper limit of the oil filler
neck. SAE 10W-30 oil is recommended for general use; for
additional recommendations, see page

If the engine is overfilled, the

excess oil may be transferred to the air cleaner housing and air filter.

Screw in the oil filler cap/dipstick securely.

Place the generator on a level surface.

Loosen the cover screw and remove the maintenance cover.

10/03/11 13:05:36 31ZT3620_081

Содержание EU 1000i





























































































Результаты поиска

Содержание EU 1000i

Отзывы:

Похожие инструкции для EU 1000i

Бренды по названию

Популярные бренды

Honda EU 1000i, Руководство пользователя

Результаты поиска

Содержание EU 1000i

Отзывы:

Похожие инструкции для EU 1000i

Бренды по названию

Популярные бренды