Honda EB5000i Скачать руководство пользователя страница 14

Страница: 14 / 96

−

CONTROL & FEATURES

CONTROLS

Fuel Valve Lever

Engine Switch

Choke Lever

FUEL VALVE LEVER

ENGINE SWITCH

CHOKE LEVER

The fuel valve must be in the ON
position for the engine to run.

After stopping the engine, turn
the fuel valve to the OFF position.

The fuel valve lever is located on
the control panel.

The engine switch controls the
ignition system.

OFF

Stops the engine.

Running position, and for

starting with the recoil starter.

The choke lever opens and closes
the choke valve in the carburetor.

The CLOSED position enriches
the fuel mixture for starting a cold
engine.

The OPEN position provides the
correct fuel mixture for operation
after starting, and for restarting a
warm engine.

04/04/28 20:53:23 31Z12600_013

Содержание EB5000i

































































































Результаты поиска

Содержание EB5000i

Отзывы:

Похожие инструкции для EB5000i

Бренды по названию

Популярные бренды

Honda EB5000i, Руководство пользователя

Результаты поиска

Содержание EB5000i

Отзывы:

Похожие инструкции для EB5000i

Бренды по названию

Популярные бренды