Honda BF10D Скачать руководство пользователя страница 102

Страница: 102 / 160

Be careful not to spill fuel.
Spilled fuel or fuel vapor may
ignite. If any fuel is spilled,
make sure the area is dry
before storing or transporting
the outboard motor.
Do not smoke or allow flames
or sparks where fuel is
drained or stored.

102

Fuel Line Removal

TRANSPORTING

10.

PULL

FUEL LINE CONNECTOR

Before transporting the outboard
motor, disconnect and remove the
fuel line in the following procedure.

While pressing the fuel line
connector clip, pull the fuel line
connector and disconnect it from
the outboard motor side joint.

While pulling the fuel line
connector cover, pull the fuel line
connector to disconnect the fuel
line connector from the fuel tank.

11/09/05 18:12:49 32ZY0620_102

Содержание BF10D

































































































































































Результаты поиска

Содержание BF10D

Отзывы:

Похожие инструкции для BF10D

Бренды по названию

Популярные бренды

Honda BF10D, Руководство пользователя

Результаты поиска

Содержание BF10D

Отзывы:

Похожие инструкции для BF10D

Бренды по названию

Популярные бренды