Honda AQUATRAX R-12X Скачать руководство пользователя страница 65

Страница: 65 / 247

Before Riding

Is Your PWC Ready To Ride?

Check that the lanyard is in
good condition and the lock
clip is securely attached.
Replace if necessary.

Insert the lock clip in the
engine stop button/switch and
check the fuel gauge.
Remove the lock clip. Add
fuel, if necessary (page 120).

Pull the reverse lever to make
sure it moves smoothly
without sticking. Check that
the bucket drops over the jet
pump steering nozzle.

Inspect for cracks or damage.
Remove any marine growth.

Check that the plugs are
secure.

Check that nothing is
obstructing the intake grate of

the jet pump, driveshaft,
cooling water filter, or
impeller. Remove any debris.

Look for anything that
appears unusual. Check that
all latches (including the seat)
are secure.

Safety
Lanyard

Fuel Level

Reverse
System

Hull

Bilge Drain
Plugs

Jet Pump
Water Intake

Loose Parts,
Latches

Содержание AQUATRAX R-12X
























































































































































































































































Результаты поиска

Содержание AQUATRAX R-12X

Отзывы:

Бренды по названию

Популярные бренды

Honda AQUATRAX R-12X, Руководство пользователя

Результаты поиска

Содержание AQUATRAX R-12X

Отзывы:

Бренды по названию

Популярные бренды