Honda AQUATRAX R-12X Скачать руководство пользователя страница 158

Страница: 158 / 247

Servicing Your Honda

151

Engine Cooling System

Always flush the engine cooling system after
using your PWC.

Flushing the system with fresh water prevents
salt water corrosion and removes silt, sand,
and other residue.

If you beach your PWC, be sure to flush the
cooling system to avoid possible engine
damage.

You may also use the flushing procedure to
provide engine cooling when you are running
the engine out of the water for maintenance
purposes.

The flushing connector is located in the jet
nozzle cavity (page 152) at the rear of your
PWC.

While flushing the system, observe the
following suggestions to avoid engine
damage or personal injury:

•

Do not touch any electrical parts or
driveshaft components while the engine is
running.

Содержание AQUATRAX R-12X
























































































































































































































































Результаты поиска

Содержание AQUATRAX R-12X

Отзывы:

Бренды по названию

Популярные бренды

Honda AQUATRAX R-12X, Руководство пользователя

Результаты поиска

Содержание AQUATRAX R-12X

Отзывы:

Бренды по названию

Популярные бренды