Honda Africa Twin CRF1000 2017 Скачать руководство пользователя страница 149

Страница: 149 / 203

Rebound Damping

You can adjust the rebound damping by the

adjuster to suit the load or the road surface.

The rebound damping adjuster has 3 turns or

more.

Turn clockwise to increase rebound damping

(hard), or turn counterclockwise to decrease

rebound damping (soft).

The standard position is 2 1/4 turns from the

maximum setting so that the punch mark on

the adjuster aligns with the reference punch

mark.

NOTICE

Do not turn the adjuster beyond its limits.

Adjust both left and right forks to the same

rebound damping.

20171109154101_32MKK8000_eng_BOOK Page 149 Thursday, November 09 2017 15:56:56 JST

Other Adjustments

Adjusting the Front Suspension

Maintenance

144

Adjusters

Reference

punch mark

Punch mark

Содержание Africa Twin CRF1000 2017












































































































































































































Результаты поиска

Содержание Africa Twin CRF1000 2017

Отзывы:

Бренды по названию

Популярные бренды

Honda Africa Twin CRF1000 2017, Руководство пользователя

Результаты поиска

Содержание Africa Twin CRF1000 2017

Отзывы:

Бренды по названию

Популярные бренды