Honda Africa Twin CRF1000 2017 Скачать руководство пользователя страница 148

Страница: 148 / 203

Adjusting the Front Suspension

Spring Preload

You can adjust the spring preload by the

adjuster to suit the load or the road surface.

Turn the adjuster using the box end wrench

provided in the tool kit.

P. 108

The spring preload adjuster has 15 turns.Turn

clockwise to increase spring preload (hard),

or turn counterclockwise to decrease spring

preload (soft).

CRF1000A/A II

The standard position is the 5 turns from the

full soft position.

CRF1000D/D II

The standard position is the 8 1/2 turns from

the full soft position.

NOTICE

Do not turn the adjuster beyond its limits.

Adjust both left and right forks to the same

spring preload.

20171109154101_32MKK8000_eng_BOOK Page 148 Thursday, November 09 2017 15:56:56 JST

Other Adjustments

Adjusting the Front Suspension

Maintenance

143

Continued

Adjuster

Содержание Africa Twin CRF1000 2017












































































































































































































Результаты поиска

Содержание Africa Twin CRF1000 2017

Отзывы:

Бренды по названию

Популярные бренды

Honda Africa Twin CRF1000 2017, Руководство пользователя

Результаты поиска

Содержание Africa Twin CRF1000 2017

Отзывы:

Бренды по названию

Популярные бренды