Honda 08B15-TR0-100A Скачать руководство пользователя страница 10

Страница: 10 / 14

10 of 14

AII 50823 (1312)

31. Using isopropyl alcohol on a shop towel, clean the

area shown on the outside of the windshield.

Q081706BK

Align.

COVER

SEAL

OUTSIDE

Clean with

isopropyl

alcohol.

32. Remove the adhesive backing from the cover seal,

and attach it to the outside of the windshield,
positioned over the antenna.

33. Cut one aluminum tape as shown.

Q092106BK

ALUMINUM

TAPE

(Cut.)

ANTENNA

PASSENGER’S



A-PILLAR

(Clean with



isopropyl



alcohol.)

ANTENNA

CABLE

34. Using isopropyl alcohol on a shop towel, clean the

passenger’s A-pillar.

35. Route the antenna cable along the passenger’s A-

pillar. Using four pieces of aluminum tape, secure
the antenna cable to the passenger’s A-pillar in the
areas shown.



NOTE: Do not attach the aluminum tape over any
vehicle holes, pay attention to the orientation of the
aluminum tape.

36. Route the antenna cable down. In the glove box

opening, route the antenna cable along the vehicle
harness and towards the passenger’s seat.

Q091704AK

GLOVE BOX

OPENING

WIRE TIE

(Loosely secure.)

ANTENNA

CABLE

VEHICLE

HARNESS

37. Loosely secure the antenna cable to the vehicle

harness with one wire tie.

Содержание 08B15-TR0-100A















Результаты поиска

Содержание 08B15-TR0-100A

Отзывы:

Бренды по названию

Популярные бренды

Honda 08B15-TR0-100A, Руководство по установке

Результаты поиска

Содержание 08B15-TR0-100A

Отзывы:

Бренды по названию

Популярные бренды