7
FCC Compliance
The HWI-TEL9 complies with Part 68 of the FCC
rules. On the front lid of this equipment is a label that
contains, among other information, the FCC
registration number and ringer equivalence number
(REN- 0.6A) for this equipment. If requested, this
information must be provided to the telephone
company.
The only registration jack USOC contained on the
HWI-TEL9 is RJ-14C and is FCC compliant. This
equipment is designed to be connected to the
telephone network or premises wiring using a
compatible telephone cord and modular plug which is
Part 68 compliant.
The REN is used to determine the quantity of devices
which may be connected to the telephone line.
Excessive RENs on the telephone line may result in
the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line,
as determined by the total RENs, contact the local
telephone company.
If the terminal equipment HWI-TEL9 causes harm to
the telephone network, the telephone company will
notify you in advance that temporary discontinuance
of service may be required. But if advance notice is
not practical, the telephone company will notify the
customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC
if you believe it is necessary.
The telephone company may make changes in it’s
facilities, equipment, operations or procedures that
could affect the operation of this equipment. If this
happens the telephone company will provide advance
notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, please
contact Lutron Electronics on 7200 Suter Road, in
Coopersburg, PA 18036, 1-800-523-9466 for repair
and/or warranty information. If the trouble is causing
harm to the telephone network, the telephone
company may request you remove the equipment
from the network until the problem is resolved.
The customer can make repairs to the phone wiring
for any inside or outside phone lines connected to the
HWI-TEL9. The customer can replace the 18 V
plug-in transformer.
The HWI-TEL9 cannot be used on public coin phone
service provided by the telephone company.
Connection to party line service is subject to state
tariffs. (Contact the state public utility commission,
public service commission or corporation commission
for information.)
Warning:
Changes or modifications to this unit not
expressly approved by the party responsible for
Lockout
After three consecutive wrong password attempts, in
either of the two Answering Machine Modes, the
system will lock out any outside access for thirty
minutes.
Use
Upon accessing the system, the user will hear
messages describing the current state of any
functions which are in the Status List. This message
will always include the status of the Security System
and Vacation Mode. Other button functions can also
be added to this list (see
Status List
on page 5)
Checking System Status
After accessing the system from an inside phone
using the Pickup Code or from an outside phone
using the Access Code, the system responds with the
list of status conditions. Repeat the Status List or
check the status of a specific button as follows:
1.
Press “*” twice for the system to list the status of
the Security System, Vacation Mode, and any of
the ten button functions programmed on the
Status List.
2.
Alternatively, press “*,” then “n” (any button 0
through 9) for the system to state the status of
button “n” only.
Activating/Deactivating Events
After accessing the system from an inside phone
using the Pickup Code or from an outside phone
using the Access Code, the system responds with the
list of status conditions.
To control a function programmed to a specific
button, press the button to which the event is
programmed. The system responds with the button
label and new status.
Ending Access to the System
When you have finished accessing the system, simply
hang up at any point. The HWI-TEL9 will reset within
15 seconds.
During system access, if no tones (button presses)
are entered into the system within a 15-second
period, the HWI-TEL9 automatically disconnects,
even if the handset is still off-hook.
