Homelite UT10927A Скачать руководство пользователя | Manualshive

Страница: 32 / 36

background image

Page 32

CLEANING THE SPARK ARRESTING
MUFFLER

The muffler is equipped with a spark arrestor screen. A
faulty spark arrestor screen can create a fire hazard.
Through normal use the screen can become dirty and
should be inspected weekly and cleaned as required.
Always keep the muffler and spark arrestor on your saw in
good condition.

WARNING

Muffler surfaces are very hot during and after
operation of the chain saw, keep all body parts away
from the muffler. Serious burns may occur if contact is
made with the muffler.

1.

Allow the muffler to cool.

2.

The spark arrestor screen is retained by the deflector.
Remove the nuts and screen retainer to access the
spark arrestor screen.

3.

Replace the spark arrestor screen if it is cracked or
otherwise deteriorated.

CHAIN BRAKE

■

Remove the clutch cover and clean the chain brake
components. Check wear on the brake band and
replace if worn or deformed. The band thickness should
not be less than 0.024 in. (.60mm), or worn halfway
through.

■

Always keep the chain brake mechanism clean and
lightly lubricate the linkage.

■

Always test the chain brake performance after servicing
or cleaning. Refer to “Operation - Operating Chain
Brake” earlier in this manual for additional information.

■

Check and, if damaged, replace the chain catcher.

STORING THE CHAIN SAW (1 MONTH OR
LONGER)

1.

Drain all fuel from tank into a container approved for
gasoline.

2.

Run the engine until it stops. This will remove all fuel-oil
mix that could become stale and leave varnish and gum
in the fuel system.

3.

Drain all bar and chain oil from tank into a container
approved for oil.

4.

Clean all foreign material from the saw.

5.

Store it in a well-ventilated place that is inaccessible to
children.

Note:

Keep away from corrosive agents such as garden

chemicals and deicing salts.

Abide by all federal and local regulations for the safe
storage and handling of gasoline. Excess fuel should be
used in other 2-cycle engine powered equipment.

BRAKE BAND

CLEAN THE CHAIN BRAKE

LUBRICATE THE CHAIN

BRAKE LINKAGE

MUFFLER

SPARK ARRESTOR

SCREEN

Fig. 79

Fig. 80

CHAIN CATCHER

Fig. 81

NUTS

MAINTENANCE

«
...
30
31
32
33
34
...
»

Содержание UT10927A





































Отзывы:

Нет отзывов

Похожие инструкции для UT10927A

Бренд: Gardenline Страницы: 22

Бренд: YATO Страницы: 96

Бренд: McCulloch Страницы: 2

Бренд: Parkside Страницы: 92

Бренд: Hitachi Koki Страницы: 7

Бренд: Stanley Страницы: 33

Бренд: Echo Страницы: 20

Бренд: Echo Страницы: 36

Бренд: Poulan Pro Страницы: 21

Бренд: Sandrigarden Страницы: 144

Бренд: Rona Страницы: 4

Бренд: Yardworks Страницы: 14

Бренд: Nakayama Страницы: 22

Бренд: EINHELL Страницы: 100

Бренд: EINHELL Страницы: 112

Бренд: Poulan Pro Страницы: 3

Бренд: ICS Страницы: 84

Бренд: Husqvarna Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды