background image

12

trouBlesHooting

ProBleM

Cause

solution

Engine fails to 

start

1. No fuel in tank 

1. Fill tank.

2. Spark plug shorted or fouled

2. Replace spark plug.

3.  Spark plug is broken (cracked 

porcelain or electrodes broken) 

3. Replace spark plug.

4.  Ignition lead wire shorted, broken, 

or disconnected form spark plug.

4. Replace lead wire or attach to spark plug.

5. Ignition inoperative

5. Contact authorized service centre.

Engine hard to 

start

1. Water in petrol 
2. Weak spark at spark plug

1. Drain entire system and refill with fresh fuel 

2. Contact authorized service centre

Engine lacks 

power

Dirty air filter

Clean or replace air filter

Detergent fails to 

mix with spray

1.  Detergent injection hose is not  

properly submerged

2. High pressure nozzle attached 

1. Insert injection hose into detergent container or 

detergent bottle
2. Use low pressure nozzle (black) to apply 

detergent

Pump doesn’t 

produce pressure

1. Low pressure nozzle installed 
2. Inadequate water supply 
3. Gun or lance leaks 

4. Nozzle is clogged 
5. Pump is faulty 

1. Replace with high pressure nozzle 

2. Provide adequate water flow 
3.   Check connections and / or replace gun or 

lance

4. Clean nozzle
5. Contact authorized service centre

Machine doesn’t 

reach high 
pressure 

1.  Diameter of garden hose is too 

small

2. Water supply is restricted

3. Not enough inlet water
4. Wrong nozzle attached

1. Replace with 12mm garden hose.

2.Check garden hose for kinks, leaks, and 

blockages.
3. Open water source full force
4. Attach the high pressure nozzle.

Содержание HPW2600

















Отзывы: